Icom IC-7610 Instruction Manual basic - Page 76

X-verter, Ant 1 / Ant 2, Rx-ant In/out

Get Icom IC-7610 PDF manuals and user guides View all Icom IC-7610 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

13 CONNECTOR INFORMATION X-VERTER Outputs HF frequency signals for the Transverter operation. ••Input/Output impedance: 50 Ω (unbalanced) ••Output signal level: More than -20 dBm LSet the "Transverter Function" item to ON to use the transverter operating mode. MENU » SET > Function > Transverter Function ••You cannot select the antenna or use the internal antenna tuner while the Transverter function is ON. LSet the offset frequency for the transverter operation. MENU » SET > Function > Transverter Offset ANT 1 / ANT 2 Connect a 50 Ω antenna for the HF to 50 MHz frequency band. ••Input/Output impedance: 50 Ω (unbalanced) RX-ANT IN/OUT Connect a receive antenna to [RX-ANT IN], and a receiver to [RX-ANT OUT]. ••Input/Output impedance: 50 Ω (unbalanced) ••Connector type: BNC LSignal is directly received through [RX-ANT IN], instead of the antenna connector. You can also connect an external preamp or filter, as shown below. LIn this case, set the antenna connector to "ANT 1/R" or "ANT 2/R." (p. 7-1) Example Transmitter TX [ANT 1] [ANT 2] RX [RX-ANT] OUT Filter IN MAIN receiver SUB receiver LIf you are using the AH-4, connect it to [ANT 1]. 13-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
13
CONNECTOR INFORMATION
13-6
X-VERTER
Outputs HF frequency signals for the
Transverter operation.
•
Input/Output impedance:
50 Ω (unbalanced)
• Output signal level:
More than –20 dBm
L
Set the “Transverter Function” item to ON to use the
transverter operating mode.
MENU
»
SET > Function >
Transverter Function
• You cannot select the antenna or use the internal
antenna tuner while the Transverter function is
ON.
L
Set the offset frequency for the transverter
operation.
MENU
»
SET > Function >
Transverter Offset
ANT 1 / ANT 2
Connect a 50 Ω antenna for the HF to 50 MHz
frequency band.
•
Input/Output impedance: 50 Ω (unbalanced)
L
If you are using the AH-4, connect it to [ANT 1].
RX-ANT IN/OUT
Connect a receive antenna to
[RX-ANT IN], and a receiver to
[RX-ANT OUT].
•
Input/Output impedance: 50 Ω (unbalanced)
• Connector type:
BNC
L
Signal is directly received through [RX-ANT IN],
instead of the antenna connector.
You can also connect an external preamp or filter, as
shown below.
L
In this case, set the antenna connector to “ANT 1/R”
or “ANT 2/R.” (p. 7-1)
IN
[RX-ANT]
[ANT 2]
[ANT 1]
OUT
TX
RX
Filter
MAIN receiver
SUB receiver
Transmitter
Example