Icom IC-7610 Instruction Manual basic - Page 65

MAINTENANCE, Resetting

Get Icom IC-7610 PDF manuals and user guides View all Icom IC-7610 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

10 MAINTENANCE Resetting Occasionally, erroneous information may be displayed. This may be caused by static electricity or by other factors. If this problem occurs, turn OFF the transceiver. After waiting a few seconds, turn ON the transceiver again. If the problem still exists, perform a Partial reset, as described to the right. If the problem still exists after a Partial reset, perform an All reset, as described to the right. NOTE: An All reset clears all data and returns all settings to their factory defaults. Save memory channel content, setting status, and so on, onto an SD card before an All reset. (p. 10-1) DDPartial reset 1. Open the RESET screen. 1 MENU » SET > Others > Reset 2 2. Touch "Partial Reset." 3 4 5 ••The confirmation screen is displayed. 6 3. Touch [Yes]. L After the resetting, the default VFO mode screen is displayed. 7 8 After performing a Partial reset A Partial reset resets operating settings to their default 9 values (VFO frequency, VFO settings, menu contents) without clearing the items listed below: 10 ••Memory channel contents ••Fixed Edges on the Spectrum Scope 11 ••Network settings in the set mode ••MY Call ••REF Adjust DDAll reset 1. Open the RESET screen. 12 MENU » SET > Others > Reset 13 2. Touch "All Reset." After performing an All reset 14 All reset clears all data and returns all settings to their factory defaults. Memory channel contents, filter setting and so on 15 will all be cleared, so you will need to rewrite your operating settings, unless you have a backup. 16 ••The confirmation screen is displayed. 17 When you cannot enter the Set mode If a touch screen operation error or an unexpected 3. Touch [NEXT]. 18 operation occurs, you cannot enter the Set mode. In this case, perform an All reset, as described below: 19 While holding down MAIN/SUB and CHANGE , 20 push POWER . 21 4. After carefully reading the displayed message, touch [YES] to perform the All reset. LAfter the resetting, the default VFO mode screen is displayed. 10-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
10
MAINTENANCE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
10-1
Resetting
Occasionally, erroneous information may be
displayed. This may be caused by static electricity or
by other factors.
If this problem occurs, turn OFF the transceiver. After
waiting a few seconds, turn ON the transceiver again.
If the problem still exists, perform a
Partial reset,
as
described to the right.
If the problem still exists after a Partial reset, perform
an
All reset,
as described to the right.
NOTE:
An All reset clears all data and returns all settings
to their factory defaults. Save memory channel content,
setting status, and so on, onto an SD card before an All
reset. (p. 10-1)
After performing a Partial reset
A Partial reset resets operating settings to their default
values (VFO frequency, VFO settings, menu contents)
without clearing the items listed below:
• Memory channel contents
• Fixed Edges on the Spectrum Scope
• Network settings in the set mode
• MY Call
• REF Adjust
After performing an All reset
All reset clears all data and returns all settings to their
factory defaults.
Memory channel contents, filter setting and so on
will all be cleared, so you will need to rewrite your
operating settings, unless you have a backup.
When you cannot enter the Set mode
If a touch screen operation error or an unexpected
operation occurs, you cannot enter the Set mode. In
this case, perform an All reset, as described below:
While holding down
MAIN/SUB
and
CHANGE
,
push
POWER
.
D
Partial reset
1.
Open the RESET screen.
MENU
»
SET > Others >
Reset
2. Touch “Partial Reset.”
•
The confirmation screen is displayed.
3. Touch [Yes].
L
After the resetting, the default VFO mode screen is
displayed.
D
All reset
1.
Open the RESET screen.
MENU
»
SET > Others >
Reset
2. Touch “All Reset.”
•
The confirmation screen is displayed.
3. Touch [NEXT].
4.
After carefully reading the displayed message,
touch [YES] to perform the All reset.
L
After the resetting, the default VFO mode screen is
displayed.