Icom IC-7610 Instruction Manual basic - Page 59
Network, CI-V USB/LAN→REMOTE Transceive Address
View all Icom IC-7610 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 59 highlights
SET MODE 8 MENU » SET > Connectors > CI-V CI-V Baud Rate (Default: Auto) Selects the CI-V data transfer rate. LWhen "Auto" is selected, the baud rate is automatically set according to the data rate of the connected device. CI-V Address (Default: 98) Sets the CI-V address. L"98h" is the default address of the IC-7610. CI-V Transceive (Default: ON) Turns the Transceive function ON or OFF. CI-V USB/LAN→REMOTE Transceive Address (Default: 00) Sets the address used to remotely control the transceiver or receiver using the optional RS-BA1, through the [USB] port. The external equipment control signal is output from the [REMOTE] port. CI-V Output (for ANT) (Default: OFF) Enables outputting the antenna controller status (frequency and so on) from the [REMOTE] port. LAddress "01h" is reserved. The usable addresses are limited to 02h ~ DFh. CI-V USB Port (Default: Unlink from [REMOTE]) Selects the internal connection type between the [USB] and [REMOTE] CI-V ports. CI-V USB Baud Rate (Default: Auto) Selects the CI-V data transfer rate when remotely controlling the IC-7610 through the [USB] CI-V port. LWhen "Auto" is selected, the baud rate is automatically set according to the data rate of external device. LThis setting is valid only when the "CI-V USB Port" item is set to "Unlink from [REMOTE]." CI-V USB Echo Back (Default: OFF) Turns the Data Echo Back function ON or OFF, when remotely controlling the IC-7610 through the [USB] CI-V port. LThis setting is valid only when the "CI-V USB Port" item is set to "Unlink from [REMOTE]." MENU » SET > Connectors > External Meter External Meter Output (MAIN) External Meter Output (SUB) (Default: Auto) (Default: Auto) Selects the parameter (Main and Sub readout) to output to an external meter. External Meter Level (MAIN) External Meter Level (SUB) (Default: 50%) (Default: 50%) Sets the output level to the external meter (Main and Sub band). 1 MENU » SET > Connectors 2 Decode Baud Rate 3 (Default: 9600) Selects the data transfer rate (Baud rate) of decoded signals. 4 SEND Relay Type (Default: MOS-FET) Selects the switching relay type for [RELAY]. 5 Select the suitable relay type, especially when connecting a non-Icom linear amplifier. 6 ACC BAND Voltage Output 7 (Default: TX) Selects the operating band voltage output from [ACC2] (pin 4). 8 MIC Input DC Bias 9 (Default: ON) Outputs the 8 V bias voltage (approximate) from the microphone connector (pin 1 of [MIC]). 10 REF IN (Default: OFF) Selects the transceiver's reference frequency signal source. LThis setting will be valid after restarting the transceiver. LIf the applied reference signal is off frequency, or not high enough, the IC-7610 will not work correctly. In that case, select "OFF," and then restart the IC-7610. 11 12 13 14 15 Network 16 17 MENU » SET > Network 18 DHCP (Default: ON( . . . )) Turns the DHCP function ON or OFF. 19 IP Address 20 (Default: 192.168. 0. 10) Sets the static IP address. 21 Subnet Mask (Default: 255.255.255. 0 (24 bit)) Sets the subnet mask to connect to your PC or LAN (Local Area Network), through the Ethernet. Default Gateway (Default: -) lf you are operating the IC-7610 using the optional RS-BA1, a default gateway setting is required. 8-7