Icom ID-4100A User Manual - Page 19

■ Installing in a vehicle

Get Icom ID-4100A PDF manuals and user guides View all Icom ID-4100A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

■■Installing in a vehicle CAUTION: DO NOT place the main unit or remote controller where normal operation of the vehicle may be hindered or where it could cause bodily injury. CAUTION: DO NOT place the main unit or remote controller where air bag deployment may be obstructed. CAUTION: DO NOT place the transceiver or remote controller where hot or cold air blows directly onto it. Installation example Controller DC power cable 1 INSTALLATION AND CONNECTIONS 1 You can install the main unit on the dashboard or the console of your vehicle with the optional MBF-4 mobile bracket. 1. Drill 4 holes where the mounting bracket is to be installed. LLApproximately 5.5 ~ 5.6 mm (0.21 ~ 0.22 inch)(d) when using nuts, approximately 2 ~ 3 mm (0.08 ~ 0.12 inch)(d) when using self-tapping screws. 2. Insert the supplied screws, nuts and washers through the mounting bracket and tighten. 3. Adjust the angle to suit your needs. Main unit Controller cable Battery (12 V) 25º More than 100 mm (3.9 inches) height (recommended) NOTE: Contact your car dealer or Icom dealer for advice for installing in a vehicle. Mounting nut When using selftapping screws Screw Flat washer Spring washer Nut BASIC MANUAL 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
4
1
INSTALLATION AND CONNECTIONS
1
BASIC MANUAL
■
Installing in a vehicle
CAUTION: DO NOT
place the main unit or remote
controller where normal operation of the vehicle may be
hindered or where it could cause bodily injury.
CAUTION: DO NOT
place the main unit or remote
controller where air bag deployment may be obstructed.
CAUTION: DO NOT
place the transceiver or remote
controller where hot or cold air blows directly onto it.
Controller
DC power
cable
Battery
(12 V)
Controller
cable
Main unit
Installation example
You can install the main unit on the dashboard or the
console of your vehicle with the optional MBF-4
MOBILE
BRACKET
.
1.
Drill 4 holes where the mounting bracket is to be
installed.
L
Approximately 5.5 ~ 5.6 mm (0.21 ~ 0.22 inch)(d) when
using nuts, approximately 2 ~ 3 mm (0.08 ~ 0.12 inch)(d)
when using self-tapping screws.
2.
Insert the supplied screws, nuts and washers through
the mounting bracket and tighten.
3.
Adjust the angle to suit your needs.
Mounting
nut
Nut
Spring washer
When using self-
tapping screws
Flat washer
Screw
25º
More than 100 mm
(3.9 inches) height
(recommended)
NOTE:
Contact your car dealer or Icom dealer for advice
for installing in a vehicle.