Icom ID-4100A User Manual - Page 22

■ Installing the UT-137

Get Icom ID-4100A PDF manuals and user guides View all Icom ID-4100A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

1 INSTALLATION AND CONNECTIONS ■■Installing the UT-137 When you install the optional UT-137 Bluetooth® unit in the transceiver, you can communicate with other Bluetooth device. WARNING! BE SURE to disconnect the DC power cable before starting the following procedures. NOTE: Before touching the transceiver or UT-137, remove static electricity from your body by touching a grounded object such as a doorknob or aluminum sash. The static electricity may damage the transceiver or the UT-137, or cause data lost. 1. Turn the transceiver upside-down. 2. Remove the four screws from the bottom of the transceiver and the four screws from the sides, then lift off the bottom cover. Bottom cover 3. Place one end the UT-137 under the edge of the front panel, with the connector facing down. Front panel UT-137 Connector 4. Carefully, push the connector into the socket. LLEnsure the UT-137 is installed correctly. 5. Reattach the bottom cover and screws. 7 BASIC MANUAL

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
7
1
INSTALLATION AND CONNECTIONS
BASIC MANUAL
■
Installing the UT-137
When you install the optional UT-137 Bluetooth
®
unit in
the transceiver, you can communicate with other Bluetooth
device.
1.
Turn the transceiver upside-down.
2.
Remove the four screws from the bottom of the
transceiver and the four screws from the sides, then lift
off the bottom cover.
WARNING! BE SURE
to disconnect the DC power cable
before starting the following procedures.
NOTE:
Before touching the transceiver or UT-137, remove
static electricity from your body by touching a grounded
object such as a doorknob or aluminum sash. The static
electricity may damage the transceiver or the UT-137, or
cause data lost.
3.
Place one end the UT-137 under the edge of the front
panel, with the connector facing down.
4.
Carefully, push the connector into the socket.
L
Ensure the UT-137 is installed correctly.
5.
Reattach the bottom cover and screws.
Bottom
cover
Front panel
UT-137
Connector