Icom ID-4100A User Manual - Page 7

WARNING! NEVER, CAUTION: DO NOT, DO NOT, BE CAREFUL, environments or in direct sunlight.

Get Icom ID-4100A PDF manuals and user guides View all Icom ID-4100A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

RRWARNING! NEVER operate the transceiver if it emits an abnormal odor, sound or smoke. Immediately turn OFF the transceiver power and remove the power cable. Contact your Icom dealer or distributor for advice. RRWARNING! NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. CAUTION: DO NOT expose the transceiver to rain, snow or any liquids. CAUTION: DO NOT change the internal settings of the transceiver. This may reduce transceiver performance and/ or damage the transceiver. CAUTION: DO NOT use harsh solvents such as Benzine or alcohol to clean the transceiver, as they will damage the transceiver's surfaces. If the transceiver becomes dusty or dirty, wipe it clean with a soft, dry cloth. CAUTION: DO NOT place or leave the transceiver in areas with temperatures below -10°C (+14°F) or above +60°C (+140°F). Be aware that temperatures on a vehicle's dashboard can exceed +80°C (+176°F) in direct sunlight, resulting in permanent damage to the transceiver if left there for long periods of time. CAUTION: DO NOT start the vehicle engine when the transceiver's power is ON. Ignition voltage spikes can damage the transceiver. CAUTION: DO NOT use non-Icom microphones. Other manufacturer's microphones have different pin assignments, and may damage the transceiver. DO NOT push the PTT when not actually desiring to transmit. DO NOT place the transceiver in excessively dusty environments or in direct sunlight. DO NOT place the transceiver against walls or putting anything on top of the transceiver. This will obstruct heat dissipation. DO NOT place the transceiver in an insecure place to avoid inadvertent use by unauthorized persons. DO NOT place the transceiver where hot or cold air blows directly onto it, during mobile operation. DO NOT operate the transceiver without running the vehicle's engine, during mobile operation. When the transceiver's power is ON and your vehicle's engine is OFF, the vehicle's battery will soon become exhausted. NOTE: During maritime mobile operation, keep the transceiver and microphone as far away as possible from the magnetic navigation compass to prevent erroneous indications. BE CAREFUL! The rear panel will become hot when continuously operating the transceiver for long periods of time. BASIC MANUAL vi

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
vi
BASIC MANUAL
R
WARNING! NEVER
operate the transceiver if it emits an
abnormal odor, sound or smoke. Immediately turn OFF the
transceiver power and remove the power cable. Contact
your Icom dealer or distributor for advice.
R
WARNING! NEVER
place the transceiver where normal
operation of the vehicle may be hindered or where it could
cause bodily injury.
CAUTION: DO NOT
expose the transceiver to rain, snow or
any liquids.
CAUTION: DO NOT
change the internal settings of the
transceiver. This may reduce transceiver performance and/
or damage the transceiver.
CAUTION: DO NOT
use harsh solvents such as Benzine
or alcohol to clean the transceiver, as they will damage the
transceiver’s surfaces. If the transceiver becomes dusty or
dirty, wipe it clean with a soft, dry cloth.
CAUTION: DO NOT
place or leave the transceiver in
areas with temperatures below –10°C (+14°F) or above
+60°C (+140°F). Be aware that temperatures on a vehicle’s
dashboard can exceed +80°C (+176°F) in direct sunlight,
resulting in permanent damage to the transceiver if left there
for long periods of time.
CAUTION: DO NOT
start the vehicle engine when the
transceiver's power is ON. Ignition voltage spikes can
damage the transceiver.
CAUTION: DO NOT
use non-Icom microphones. Other
manufacturer’s microphones have different pin assignments,
and may damage the transceiver.
DO NOT
push the PTT when not actually desiring to
transmit.
DO NOT
place the transceiver in excessively dusty
environments or in direct sunlight.
DO NOT
place the transceiver against walls or putting
anything on top of the transceiver. This will obstruct heat
dissipation.
DO NOT
place the transceiver in an insecure place to avoid
inadvertent use by unauthorized persons.
DO NOT
place the transceiver where hot or cold air blows
directly onto it, during mobile operation.
DO NOT
operate the transceiver without running the
vehicle’s engine, during mobile operation. When the
transceiver’s power is ON and your vehicle’s engine is OFF,
the vehicle’s battery will soon become exhausted.
NOTE:
During maritime mobile operation, keep the
transceiver and microphone as far away as possible from
the magnetic navigation compass to prevent erroneous
indications.
BE CAREFUL!
The rear panel will become hot when
continuously operating the transceiver for long periods of
time.