Invacare M61 Owners Manual - Page 46

Adjusting the Footboard Assembly

Get Invacare M61 PDF manuals and user guides View all Invacare M61 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

SECTION 8-FOOTBOARD ASSEMBLY Installing ƽ WARNING Make sure the detent balls of the quick-release pin are fully released beyond the outer edge of the tube before operating the wheelchair. Otherwise, injury and/or damage may result. Keep detent balls clean. 1. Position the footboard assembly onto the wheelchair frame so that the mounting hole in the wheelchair frame aligns with the desired mounting hole in the footboard assembly. 2. Install the quick release pin by depressing the button while sliding the pin in. Ensure that the detent balls of the quick release pin are fully released beyond the outer edge of the tube (Detail "A" of FIGURE 8.1). Top Shroud DETAIL "A" - BOTTOM VIEW OF FOOTBOARD Quick Release Pin Pinch Point Footboard Assembly Mounting Hole Quick Release Pin Detent Ball Outer Edge of Tube Detent Balls FIGURE 8.1 Removing/Installing the Footboard Assembly Adjusting the Footboard Assembly Angle NOTE: For this procedure, refer to FIGURE 8.2 on page 47. 1. Loosen the jam nut and set screw located underneath on the backside of the footplate. 2. Adjust the set screw in or out to obtain the desired footboard assembly angle. 3. Thread the jam nut and washer inward until it is flush with the footboard bracket. 4. Securely tighten the jam nut and washer to secure the mounting screw in place. Pronto® M51™and M61™with SureStep® 46 Part No 1125085

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
SECTION 8—FOOTBOARD ASSEMBLY
Pronto® M51™and M61™with SureStep®
46
Part No 1125085
Installing
±
WARNING
Make sure the detent balls of the quick-release pin are fully released beyond the
outer edge of the tube before operating the wheelchair. Otherwise, injury and/or
damage may result.
Keep detent balls clean.
1.
Position the footboard assembly onto the wheelchair frame so that the mounting hole
in the wheelchair frame aligns with the desired mounting hole in the footboard
assembly.
2.
Install the quick release pin by depressing the button while sliding the pin in. Ensure
that the detent balls of the quick release pin are fully released beyond the outer edge
of the tube (Detail “A” of FIGURE 8.1).
FIGURE 8.1
Removing/Installing the Footboard Assembly
Adjusting the Footboard Assembly
Angle
NOTE: For this procedure, refer to FIGURE 8.2 on page 47.
1.
Loosen the jam nut and set screw located underneath on the backside of the footplate.
2.
Adjust the set screw in or out to obtain the desired footboard assembly angle.
3.
Thread the jam nut and washer inward until it is flush with the footboard bracket.
4.
Securely tighten the jam nut and washer to secure the mounting screw in place.
DETAIL “A” - BOTTOM VIEW OF
FOOTBOARD
Quick
Release Pin
Detent
Ball
Footboard
Assembly
Mounting Hole
Top Shroud
Quick Release Pin
Outer Edge
of Tube
Detent Balls
Pinch Point