Invacare M61 Owners Manual - Page 78

Installing/Removing/Using the Walker Holder

Get Invacare M61 PDF manuals and user guides View all Invacare M61 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

SECTION 13-ACCESSORIES Installing/Removing/Using the Walker Holder ƽ INSTALLATION WARNINGS After any adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely. The installation of the walker holder onto the back of the wheelchair seat increases the length of the wheelchair up to nine inches. When turning the wheelchair it is important to take note of this increased length - otherwise, injury and/or damage to surrounding property may result. NOTE: For this procedure, refer to FIGURE 13.3. Installing/Removing the Walker Holder NOTE: Reverse this procedure to remove the walker holder. 1. If necessary, loosen but do not remove the mounting knob. 2. Install the walker holder into the accessory tube. 3. Thread the mounting knob into the welded nut on the accessory tube. Securely tighten. Using the Walker Holder 1. Fold walker. Refer to instructions provided with the walker. NOTE: Walker MUST be folded before using walker holder. 2. Hang folded walker on walker holder hooks. 3. Secure walker with hook and loop straps. Seat Walker Holder DETAIL "A" Hook Accessory Tube Hook and Loop Straps Mounting Knob FIGURE 13.3 Installing/Removing/Using the Walker Holder Pronto® M51™and M61™with SureStep® 78 Part No 1125085

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
SECTION 13—ACCESSORIES
Pronto® M51™and M61™with SureStep®
78
Part No 1125085
Installing/Removing/Using the Walker Holder
±
INSTALLATION WARNINGS
After any adjustments, repair or service and before use, make sure that all attaching
hardware is tightened securely.
The installation of the walker holder onto the back of the wheelchair seat increases
the length of the wheelchair up to nine inches. When turning the wheelchair it is
important to take note of this increased length - otherwise, injury and/or damage to
surrounding property may result.
NOTE: For this procedure, refer to FIGURE 13.3.
Installing/Removing the Walker Holder
NOTE: Reverse this procedure to remove the walker holder.
1.
If necessary, loosen but do not remove the mounting knob.
2.
Install the walker holder into the accessory tube.
3.
Thread the mounting knob into the welded nut on the accessory tube. Securely
tighten.
Using the Walker Holder
1.
Fold walker. Refer to instructions provided with the walker.
NOTE: Walker MUST be folded before using walker holder.
2.
Hang folded walker on walker holder hooks.
3.
Secure walker with hook and loop straps.
FIGURE 13.3
Installing/Removing/Using the Walker Holder
Seat
Accessory
Tube
Mounting Knob
Walker Holder
Hook and
Loop Straps
Hook
DETAIL “A”