JVC GY-DV550E Instruction Manual - Page 39

Using An Anton-bauer Battery Pack

Get JVC GY-DV550E - Studio Dv Camcorder PDF manuals and user guides View all JVC GY-DV550E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

4. POWER SUPPLY 4-2 Battery Pack Operation (Cont'd) USING AN ANTON-BAUER BATTERY PACK To use an Anton-Bauer battery pack (Propack 13/14, Trimpack 13/14, Magnum 13/14, Compack 13/14 Series), it is necessary to detach the battery case from the GY-DV550 and replace it with the Anton-Bauer battery holder. Use the following battery holder. • Battery holder: Anton-Bauer QRQ27 Detaching the Battery Case From the GY-DV550 and Attaching The Anton-Bauer Battery 2. Connector Compartment 5. 1. Black screw A 1. Remove the two black screws A on the battery case. 2. Remove the lower half of the battery case cover in the downward direction. 3. Mount screw B 3. Connector 3. Mount screw B 3. To remove the battery case, remove the four screws B fixing the battery case and the connector connecting the battery case to this unit. 5. 4. Anton-Bauer Battery holder 4. Connect the connectors protruding from the GY-DV550 with the connectors on the battery holder. * Following connection of the connectors, insert them into the connector compartment. 5. Secure the battery holder to the GY-DV550 with the four mount screws provided with the battery holder. * Take care not to pinch the wires. This could result in damage. Attaching and Detaching an Anton-Bauer Battery Pack Release lever Guide pins Cassette cover side panel Battery Guide holes pack (x3) (Trimpack) Release lever Side panel with display LIGHT ON OFF COUNTER CTL TC UB CH-1 CH-2 FRONT REAR AUDIO INPUT MODE RM VTR INCOM MIC CARBON DYNAMIC INCOM MIC ON LEVEL OFF CALL RM OFF DC IN /BATT. POWER Battery Attaching the Battery Pack 1. Align the 3 guide pins of the battery pack with the guide holes on the battery holder, and push straight to insert the battery pack. The battery cannot be attached properly if the guide pins are not inserted straight. 2. Slide the battery pack toward the side panel where the cassette cover is located until it clicks. Now the battery pack has been attached. Detaching the Battery Pack While pushing and holding the release lever, slide the battery pack toward the side panel where the LCD display is located, then pull the battery pack outward to remove. 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
4. POWER SUPPLY
39
4.
5.
5.
3.
3.
3.
1.
2.
4.
Connect the connectors protruding from the GY-DV550 with
the connectors on the battery holder.
*
Following connection of the connectors, insert them into
the connector compartment.
5.
Secure the battery holder to the GY-DV550 with the four
mount screws provided with the battery holder.
* Take care not to pinch the wires. This could result in
damage.
To use an Anton-Bauer battery pack (Propack 13/14, Trimpack 13/14, Magnum 13/14, Compack 13/14 Series), it is necessary to
detach the battery case from the GY-DV550 and replace it with the Anton-Bauer battery holder. Use the following battery holder.
•
Battery holder: Anton-Bauer QRQ27
Detaching the Battery Case From the GY-DV550 and Attaching The Anton-Bauer Battery
1.
Remove the two black screws
A
on the battery case.
2.
Remove the lower half of the battery case cover in the
downward direction.
Attaching and Detaching an Anton-Bauer Battery Pack
Attaching the Battery Pack
1.
Align the 3 guide pins of the battery pack with
the guide holes on the battery holder, and push
straight to insert the battery pack.
The battery cannot be attached properly if the
guide pins are not inserted straight.
2.
Slide the battery pack toward the side panel
where the cassette cover is located until it clicks.
Now the battery pack has been attached.
Detaching the Battery Pack
±
While pushing and holding the release lever, slide
the battery pack toward the side panel where the
LCD display is located, then pull the battery pack
outward to remove.
3.
To remove the battery case, remove the four screws
B
fixing
the battery case and the connector connecting the battery
case to this unit.
4-2
Battery Pack Operation (Cont'd)
Black screw
A
Mount screw
B
LIGHT
ON
OFF
COUNTER
CH-1
CH-2
REAR
FRONT
RM
AUDIO INPUT
MODE
CTL
TC
UB
VTR
ON
OFF
INCOM
MIC
INCOM
MIC
LEVEL
POWER
OFF
RM
DC
IN
/BATT.
CALL
CARBON
DYNAMIC
Connector
Mount screw
B
Guide pins
Battery
pack
(Trimpack)
Release
lever
Cassette cover
side panel
Guide holes
(x3)
Side panel
with display
Battery
Release lever
Anton-Bauer
Battery holder
USING AN ANTON-BAUER BATTERY PACK
Connector
Compartment