JVC V685U Instructions - Page 18

Connection/Installation (VN-V685U/VN-V686BU), Mounting the Camera

Get JVC V685U - VN Network Camera PDF manuals and user guides View all JVC V685U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Connection/Installation (VN-V685U/VN-V686BU) Mounting the Camera Preparation Be sure to put on protective glasses to protect your eyes from falling objects when mounting the camera. 1 Make holes on the ceiling ● Use the provided template to make a hole (R80 mm) for the connection cables to thread behind the ceiling. ● If necessary, also open a screw hole to mount the ceiling clamping bracket to the ceiling. In this case, align the AD FRONT markB of the template in the direction where the camera faces front and open the screw hole. 2 Pull the cables from the hole in the ceiling Pull out the fall prevention wire, power cable, coaxial cable, control signal cable, alarm signal cable and provided alarm cable that were mounted to the ceiling slab from the ceiling. 80 1 ● Doing so detaches the ceiling clamping bracket from the camera. Prevent the bracket from dropping such as by performing this on a table. Memo: ● If the camera fixing lock knob is too stiff, push the knob hard while pressing the edge of the camera unit (A in the diagram) against the table you are using. C Lifting the camera unit detaches the ceiling clamping bracket. Remove by sliding it in the direction indicated by the arrows. A A Camera fixing lock knob (x2) B B C Ceiling mount Camera 4 Remove the terminal cover Loosen two screws on the ceiling clamping bracket and remove the terminal cover. Fall Preventio LAN Cable Power cable Alarm signal cable 2 Note: ● Mount the fall prevention wire on a firm place with sufficient strength. 3 Remove the ceiling clamping bracket from the camera unit The ceiling clamping bracket is attached to the camera unit during packaging of the product. Before installing the camera, remove the ceiling clamping bracket from the camera unit. A Check to make sure that the two camera lock knobs (left and right) are unlocked. ● If they are locked, unlock by sliding them in the direction indicated by the arrow. B Press the two camera lock knobs from both the left and right sides in the direction indicated by the arrows. Terminal cover 5 Mount the fall prevention wire that connects the ceiling clamping bracket to the ceiling 6 mm Ⅵ Fall Prevention Wire 6 mm (3/16 R6 mm and R4 to 5.5 mm 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
18
Connection/Installation (VN-V685U/VN-V686BU)
Preparation
1
Make holes on the ceiling
●
Use the provided template to make a hole (
R
80
mm) for the connection cables to thread behind
the ceiling.
●
If necessary, also open a screw hole to mount the
ceiling clamping bracket to the ceiling. In this case,
align the
A
D
FRONT mark
B
of the template in the
direction where the camera faces front and open
the screw hole.
2
Pull the cables from the hole in the ceiling
Pull out the fall prevention wire, power cable, coaxial
cable, control signal cable, alarm signal cable and
provided alarm cable that were mounted to the ceiling
slab from the ceiling.
Note:
●
Mount the fall prevention wire on a firm place with
sufficient strength.
3
Remove the ceiling clamping bracket from
the camera unit
The ceiling clamping bracket is attached to the
camera unit during packaging of the product. Before
installing the camera, remove the ceiling clamping
bracket from the camera unit.
A
Check to make sure that the two camera lock knobs
(left and right) are unlocked.
●
If they are locked, unlock by sliding them in the
direction indicated by the arrow.
B
Press the two camera lock knobs from both the left
and right sides in the direction indicated by the
arrows.
●
Doing so detaches the ceiling clamping bracket
from the camera. Prevent the bracket from
dropping such as by performing this on a table.
Memo
:
●
If the camera fixing lock knob is too stiff, push the
knob hard while pressing the edge of the camera
unit (
A
in the diagram) against the table you are
using.
C
Lifting the camera unit detaches the ceiling
clamping bracket. Remove by sliding it in the
direction indicated by the arrows.
4
Remove the terminal cover
Loosen two screws on the ceiling clamping bracket
and remove the terminal cover.
5
Mount the fall prevention wire that
connects the ceiling clamping bracket to
the ceiling
Mounting the Camera
Be sure to put on protective glasses to protect
your eyes from falling objects when mounting
the camera.
1
80
2
Alarm signal
cable
Power cable
LAN Cable
Fall
Preventio
C
B
B
A
A
Camera fixing
lock knob (x2)
Camera
Ceiling mount
Terminal cover
6 mm
²
Fall Prevention Wire
6 mm (3/16
R
6 mm and
R
4 to 5.5 mm