JVC V685U Instructions - Page 20

Mounting the Camera, continued, Connection/Installation VN-V685U/VN-V686BU

Get JVC V685U - VN Network Camera PDF manuals and user guides View all JVC V685U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Connection/Installation (VN-V685U/VN-V686BU) Mounting the Camera (continued) Preparation (continued) 8 Mount the terminal cover Return the terminal cover that was removed in step 3 to its original position. The direction to pull out the cables changes according to the mounting method of the camera. Ⅵ Pulling out the cables from the side Terminal cover Mounting the ceiling clamping bracket to the ceiling 1 Secure the ceiling clamping bracket to the ceiling ● Install such that the ADFRONT markB of the ceiling clamping bracket faces the front. ● Ensure that the connection cables are not caught in between and secure the ceiling clamping bracket to the ceiling with 3 screws. Front of the camera DFRONT mark Ⅵ Pulling out the cables from the top Fall Prevention Wire (To go under the terminal cov Terminal cover Note: ● Be sure to mount the terminal cover to prevent foreign objects or dust from entering. ● When pulling out the cables from the top, make the fall prevention wire go under the terminal cover and pull it out together with the other cables. ● When pulling out the cables from the side, remove the cable cover of the camera. Cable cover 5 mm (3/16 inch) and below Screws Note: ● Use M4 fixing screws and bolts. ● Use R4.1 wood screws. ● The length of the screws should be 25 mm (1inch) and above. ● Place the product horizontally and install. The camera will not operate properly if it is slanted. ● The screw head should be 5 mm and below. If the ceiling structure is metal, image noise may occur. ● Do not use screws for which the screw head is embedded after fastening. (e.g. flat countersunk head screws). Otherwise, the insulating resin part may be damaged, thus preventing proper insulation. Memo: ● Always use 3 screws and mount securely. ● Tighten the screws again during maintenance just to be safe. ● The plastic parts on the ceiling fixing holes of the ceiling clamping bracket act as an insulation between the ceiling clamping bracket and the ceiling structure. If the ceiling structure is metal and insulation is not provided between the camera and the ceiling structure, image noise may occur. Be sure to provide insulation. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
20
Connection/Installation (VN-V685U/VN-V686BU)
Preparation (continued)
8
Mount the terminal cover
Return the terminal cover that was removed in step
3
to
its original position. The direction to pull out the cables
changes according to the mounting method of the
camera.
Note:
●
Be sure to mount the terminal cover to prevent foreign
objects or dust from entering.
●
When pulling out the cables from the top, make the
fall prevention wire go under the terminal cover and
pull it out together with the other cables.
●
When pulling out the cables from the side, remove the
cable cover of the camera.
Mounting the ceiling clamping bracket
to the ceiling
1
Secure the ceiling clamping bracket to the
ceiling
●
Install such that the
A
D
FRONT mark
B
of the ceiling
clamping bracket faces the front.
●
Ensure that the connection cables are not caught in
between and secure the ceiling clamping bracket to
the ceiling with 3 screws.
Note:
●
Use M4 fixing screws and bolts.
●
Use
R
4.1 wood screws.
●
The length of the screws should be 25 mm (1inch)
and above.
●
Place the product horizontally and install. The camera
will not operate properly if it is slanted.
●
The screw head should be 5 mm and below. If the
ceiling structure is metal, image noise may occur.
●
Do not use screws for which the screw head is
embedded after fastening. (e.g. flat countersunk head
screws). Otherwise, the insulating resin part may be
damaged, thus preventing proper insulation.
Memo
:
●
Always use 3 screws and mount securely.
●
Tighten the screws again during maintenance just to
be safe.
●
The plastic parts on the ceiling fixing holes of the
ceiling clamping bracket act as an insulation between
the ceiling clamping bracket and the ceiling structure.
If the ceiling structure is metal and insulation is not
provided between the camera and the ceiling
structure, image noise may occur. Be sure to provide
insulation.
Mounting the Camera
(continued)
²
Pulling out the cables from the top
Terminal cover
Fall Prevention Wire
(To go under the terminal cov
²
Pulling out the cables from the side
Terminal
cover
Cable cover
Screws
D
FRONT mark
Front of the camera
5 mm (3/16
inch) and below