JVC V685U Instructions - Page 28

LAN Cable Connection

Get JVC V685U - VN Network Camera PDF manuals and user guides View all JVC V685U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Connection/Installation (VN-V686WPBU) Mounting the Camera (continued) Mounting the Camera 1 Mount the fall prevention wire ● Mount the fall prevention wire of the camera to the fall prevention wire anchor bolt that was installed earlier. ● Secure the fall prevention wire tightly with a nut and washer. 2 Pull out the cables (from the wall) from the cable connection hole. 3 Mount the camera to the wall ● Mount the camera to the camera anchor bolts that were installed earlier. ● Secure the camera tightly with a nut and washer. Cable Connection 1 Connecting the power cable (A Page 30) Connect the power cable and wind the waterproof tape (adhesive). After connecting, push the cable into the arm of the camera. Arm 3 Washer Nut 1 Fall Prevention Wire 2 Wind the waterproof tape (adhesive) 2 LAN Cable Connection (A Page 31) A Use the provided RJ-45 conversion connector and connect the LAN cable. B Wind the connector section with waterproof tape (adhesive) and push the cable into the arm of the camera. Arm Note: ● This product weighs approximately 5.5kg. When installing, pay extra attention as it may fall. ● For your safety, hold the arm section during installation. ● After installing, paint the nuts and washers to prevent corrosion. A Memo: ● To remove the camera, follow the reverse procedures. B Wind the waterproof tape (adhesive) 28 RJ-45 conversion connector (provided)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
28
Connection/Installation (VN-V686WPBU)
Mounting the Camera
1
Mount the fall prevention wire
●
Mount the fall prevention wire of the camera to the fall
prevention wire anchor bolt that was installed earlier.
●
Secure the fall prevention wire tightly with a nut and
washer.
2
Pull out the cables (from the wall) from the
cable connection hole.
3
Mount the camera to the wall
●
Mount the camera to the camera anchor bolts that
were installed earlier.
●
Secure the camera tightly with a nut and washer.
Note:
●
This product weighs approximately 5.5k
g
. When
installing, pay extra attention as it may fall.
●
For your safety, hold the arm section during
installation.
●
After installing, paint the nuts and washers to prevent
corrosion.
Memo
:
●
To remove the camera, follow the reverse procedures.
Cable Connection
1
Connecting the power cable
(
A
Page 30)
Connect the power cable and wind the
waterproof tape (adhesive).
After connecting, push the cable into the arm of
the camera.
2
LAN Cable Connection (
A
Page 31)
A
Use the provided RJ-45 conversion connector
and connect the LAN cable.
B
Wind the connector section with waterproof
tape (adhesive) and push the cable into the
arm of the camera.
Mounting the Camera
(continued)
1
2
3
Fall Prevention
Wire
Washer
Nut
Wind the waterproof tape (adhesive)
Arm
B
A
Wind the
waterproof tape
(adhesive)
Arm
RJ-45
conversion
connector
(provided)