Kyocera KM-2030 Print System K Instruction Handbook (Functions) - Page 10

Receive dump mode, Printer reset, Resource protect mode, Auto Continue ON/OFF, Recovery time - error codes

Get Kyocera KM-2030 PDF manuals and user guides View all Kyocera KM-2030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

1. Printer Settings (15 ppm copier) Menu number Item Available settings P71 Receive dump mode (1) OK The data that the printer receives for debugging programs and files is turned into hexadecimal code and printed out. If "OK" (setting: 1) is selected here, this receive dump mode will be activated. The receive dump mode will be canceled under the following circumstances: • The Start key is pressed in the printer mode. • A force-print time-out occurs. P72 Printer reset (1) OK Resets the Printer Board only even without turning the power to the machine OFF. P73 Resource protect mode (1) Off Protects the resource data of fonts and macros (2) Permanent downloaded through PCL6 and, even if the emula- (3) Permanent/Temporary tion protocol is switched, the PCL resource will be saved in the printer's memory. If "Permanent" (setting: 2) is selected here, temporary resources will not be saved. If, however, "Permanent/Tempo- rary" (setting: 3) is selected, temporary resources will also be saved. Permanent/Temporary P74 Auto Continue ON/OFF (1) On If one of the following error messages appears and (2) Off "On" has been selected here, the error state will be released and the printing operation will be restarted automatically after a specified amount of time. "Memory overflow (error code : E70)" "Print overrun (error code : E80)" P75 Recovery time for Auto Continue 000 - 495 (sec.) Sets the amount of time before Auto Continue engages when "On" (setting: 1) is selected under the "Auto Continue ON/OFF" setting (menu: P74). If "000" seconds is selected here, Auto Continue will engage immediately after the error. P76 Service Rep Status Page print out Prints out a Status Page for use by your service representative. - - - Remarks At least 16 MB of additional memory (option) must be installed. Print out will begin as soon as the corresponding menu number is displayed and the Enter key pressed. 1-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
1-6
1. Printer Settings (15 ppm copier)
Menu
number
P71
P72
P73
P74
P75
P76
Item
Receive dump mode
The data that the printer receives for debugging
programs and files is turned into hexadecimal code
and printed out. If “OK” (setting: 1) is selected here,
this receive dump mode will be activated. The
receive dump mode will be canceled under the
following circumstances:
• The Start key is pressed in the printer mode.
• A force-print time-out occurs.
Printer reset
Resets the Printer Board only even without turning
the power to the machine OFF.
Resource protect mode
Protects the resource data of fonts and macros
downloaded through PCL6 and, even if the emula-
tion protocol is switched, the PCL resource will be
saved in the printer’s memory. If “Permanent”
(setting: 2) is selected here, temporary resources
will not be saved. If, however, “Permanent/Tempo-
rary” (setting: 3) is selected, temporary resources
will also be saved.
Permanent/Temporary
Auto Continue ON/OFF
If one of the following error messages appears and
“On” has been selected here, the error state will be
released and the printing operation will be restarted
automatically after a specified amount of time.
“Memory overflow (error code : E70)”
“Print overrun (error code : E80)”
Recovery time for Auto Continue
Sets the amount of time before Auto Continue
engages when “On” (setting: 1) is selected under the
“Auto Continue ON/OFF” setting (menu: P74). If
“000” seconds is selected here, Auto Continue will
engage immediately after the error.
Service Rep Status Page print out
Prints out a Status Page for use by your service
representative.
Available settings
(1) OK
(1) OK
(1) Off
(2) Permanent
(3) Permanent/Temporary
(1) On
(2) Off
000 - 495 (sec.)
– – –
Remarks
At least 16 MB of additional memory
(option) must be installed.
Print out will begin as soon as the
corresponding menu number is
displayed and the Enter key pressed.