Kyocera KM-2030 Print System K Instruction Handbook (Functions) - Page 19

automatically turn Protect ON. If

Get Kyocera KM-2030 PDF manuals and user guides View all Kyocera KM-2030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

2. Printer Settings (20 ppm copier) Item No. Item Display message Available settings Remarks 23 Page Protect If "AUTO" is selected here, the machine will monitor the data and, if necessary, will automatically turn Page Protect ON. If a "Print overrun" error does happen to occur even then, the machine will automatically change the Page Protect setting to "ON". Page Protect Auto, On 24 Line Feed (LF) handling LF Action LF only, CR and LF, Ignore LF Allows you to set different line feed handling for the parallel interface and the Network Card (option). Select the desired interface under the "Interface selection" setting (item No.: 2). 25 Carriage Return (CR) handling CR Action CR only, CR and LF, Ignore CR Allows you to set different carriage return handling for the parallel interface and the Network Card (option). Select the desired interface under the "Interface selection" setting (item No.: 2). 26 Wide A4 ON/OFF Increases the printing area on A4 size paper. Wide A4 On, Off 27 Smoothing ON/OFF Allows a printing resolution of an interpo- lated 2400 dpi x 600 dpi through the smoothing process. KIR Mode On, Off 28 EcoPrint ON/OFF Ecoprint Mode On, Off Allows printing in a toner-saving mode. This mode is especially suited for test pages, etc., where high printing quality is not required. 29 Printing resolution Resolution 300 dpi, 600 dpi 30 RAM disk ON/OFF RAM DISK Mode On, Off At least 16 MB of additional memory (option) must be installed. 31 RAM disk size RAM DISK Size 01 - 99 (MBytes) Sets the amount of memory that will be used as a RAM disk. The maximum size that can be selected is the total amount of memory installed minus the amount used by the system (9 MB). Displayed only when "On" is selected under the "RAM disk ON/ OFF" setting (item No.: 30). 32 Reading data Reads the selected data on the RAM disk. Read Data Select the name of the partition which holds the data from among those displayed. Displayed only when there is appropriate data in the RAM disk. 33 Reading program data Reads the selected program data on the RAM disk. Read Program Select the name of the partition which holds the program from among those displayed. Displayed only when there is appropriate program data in the RAM disk. 34 Writing data If "OK" is selected here, the machine will enter a "waiting for data" state until data is sent from the host computer. To exit this state, select the "GO" command in the printer mode and then press the Enter key. Write Data OK 2-9 Displayed only when "On" is selected under the "RAM disk ON/ OFF" setting (item No.: 30).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
2-9
2. Printer Settings (20 ppm copier)
Item No.
23
24
25
26
27
28
29
30
31
32
33
34
Item
Page Protect
If “AUTO” is selected here, the machine will
monitor the data and, if necessary, will
automatically turn Page Protect ON. If a
“Print overrun” error does happen to occur
even then, the machine will automatically
change the Page Protect setting to “ON”.
Line Feed (LF) handling
Carriage Return (CR) handling
Wide A4 ON/OFF
Increases the printing area on A4 size paper.
Smoothing ON/OFF
Allows a printing resolution of an interpo-
lated 2400 dpi x 600 dpi through the
smoothing process.
EcoPrint ON/OFF
Allows printing in a toner-saving mode. This
mode is especially suited for test pages, etc.,
where high printing quality is not required.
Printing resolution
RAM disk ON/OFF
RAM disk size
Sets the amount of memory that will be used
as a RAM disk. The maximum size that can
be selected is the total amount of memory
installed minus the amount used by the
system (9 MB).
Reading data
Reads the selected data on the RAM disk.
Reading program data
Reads the selected program data on the
RAM disk.
Writing data
If “OK” is selected here, the machine will
enter a “waiting for data” state until data is
sent from the host computer. To exit this
state, select the “GO” command in the
printer mode and then press the Enter key.
Display message
Page Protect
LF Action
CR Action
Wide A4
KIR Mode
Ecoprint Mode
Resolution
RAM DISK Mode
RAM DISK Size
Read Data
Read Program
Write Data
Available settings
Auto, On
LF only,
CR and LF,
Ignore LF
CR only,
CR and LF,
Ignore CR
On, Off
On, Off
On, Off
300 dpi, 600 dpi
On, Off
01 - 99 (MBytes)
Select the name of
the partition which
holds the data from
among those
displayed.
Select the name of
the partition which
holds the program
from among those
displayed.
OK
Remarks
Allows you to set different line
feed handling for the parallel
interface and the Network Card
(option). Select the desired
interface under the “Interface
selection” setting (item No.: 2).
Allows you to set different carriage
return handling for the parallel
interface and the Network Card
(option). Select the desired
interface under the “Interface
selection” setting (item No.: 2).
At least 16 MB of additional
memory (option) must be installed.
Displayed only when “On” is
selected under the “RAM disk ON/
OFF” setting (item No.: 30).
Displayed only when there is
appropriate data in the RAM disk.
Displayed only when there is
appropriate program data in the
RAM disk.
Displayed only when “On” is
selected under the “RAM disk ON/
OFF” setting (item No.: 30).