Lenovo ThinkCentre M72z Hardware Maintenance Manual (HMM) for ThinkCentre M72z - Page 109

Grasp the microprocessor on the sides and lift it straight up and out of the socket. Do not touch

Get Lenovo ThinkCentre M72z PDF manuals and user guides View all Lenovo ThinkCentre M72z manuals
Add to My Manuals
Save this manual to your list of manuals

Page 109 highlights

Figure 40. Removing the seven screws that secure the system board to the main bracket 13. Place the new system board into the chassis and align the screw holes with those in the chassis. 14. Reinstall the seven screws that secure the system board to the main bracket. 15. Reinstall the rear I/O assembly. See "Replacing the rear I/O assembly" on page 84. 16. Reinstall the battery. See "Replacing the battery" on page 96. 17. Reinstall the memory modules. See "Installing or replacing a memory module" on page 98. 18. Reinstall the microprocessor. See "Replacing the microprocessor" on page 91. 19. Reinstall the heat sink assembly. See "Replacing the heat sink assembly" on page 89. 20. Reinstall the system board shield. See "Removing and reinstalling the system board shield" on page 86. 21. Reconnect all cables that were disconnected from the system board. See "System board parts and connectors" on page 70. 22. Go to "Completing the parts replacement" on page 109. The failing system board must be returned with a microprocessor socket cover to protect the pins during shipping and handling. To install the microprocessor socket cover, do the following: 1. Release the lever securing the microprocessor retainer and open the retainer to access the microprocessor. 2. Grasp the microprocessor on the sides and lift it straight up and out of the socket. Do not touch the contacts on the microprocessor socket. 3. Note the orientation of the socket cover. Align the notches 1 on the microprocessor socket cover with the alignment keys 2 on the microprocessor socket. Install one side of the socket cover into the microprocessor socket. Chapter 9. Replacing FRUs 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Figure 40. Removing the seven screws that secure the system board to the main bracket
13. Place the new system board into the chassis and align the screw holes with those in the chassis.
14. Reinstall the seven screws that secure the system board to the main bracket.
15. Reinstall the rear I/O assembly. See “Replacing the rear I/O assembly” on page 84.
16. Reinstall the battery. See “Replacing the battery” on page 96.
17. Reinstall the memory modules. See “Installing or replacing a memory module” on page 98.
18. Reinstall the microprocessor. See “Replacing the microprocessor” on page 91.
19. Reinstall the heat sink assembly. See “Replacing the heat sink assembly” on page 89.
20. Reinstall the system board shield. See “Removing and reinstalling the system board shield” on page 86.
21. Reconnect all cables that were disconnected from the system board. See “System board parts and
connectors” on page 70.
22. Go to “Completing the parts replacement” on page 109.
The failing system board must be returned with a microprocessor socket cover to protect the pins during
shipping and handling.
To install the microprocessor socket cover, do the following:
1. Release the lever securing the microprocessor retainer and open the retainer to access the
microprocessor.
2. Grasp the microprocessor on the sides and lift it straight up and out of the socket. Do not touch the
contacts on the microprocessor socket.
3. Note the orientation of the socket cover. Align the notches
1
on the microprocessor socket cover
with the alignment keys
2
on the microprocessor socket. Install one side of the socket cover into
the microprocessor socket.
Chapter 9
.
Replacing FRUs
103