Lexmark W820 Setup Guide - Page 73

Attaching the finisherplate andguiderail, the line on the holding plate

Get Lexmark W820 - Optra B/W Laser Printer PDF manuals and user guides
UPC - 734646210508
View all Lexmark W820 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Sticker Guide rail Attaching the finisher plate and guide rail Finisher plate Guide rail holding plate Alignment knobs 1 Line up the thumbscrews on the finisher plate with the two holes on the right side of the printer. Be sure to orient the plate so that it does not cover the socket directly above it. 2 Secure the finisher plate to the printer using the thumbscrews. 3 Orient the holding plate with the screws as shown. 4 Slide the bottom lip under the printer. 5 Pull the holding plate upward to align the thumbscrews in the plate with the holes in the side of the printer. 6 Secure the holding plate to the printer using the thumbscrews. 7 Align the thumbscrews on the guide rail with the holes in the holding plate and start the thumbscrews, but do not tighten them. 8 Align the top of the guide rail with the line on the holding plate by rotating the two alignment knobs closest to the holding plate. This action raises or lowers the guide rail, depending on which way the knobs are turned. The edge of the guide rail should line up with the sticker where the white and gray portions divide. 9 Secure the guide rail to the holding plate by tightening the thumbscrews. Set up the optional finisher 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
61
Set up the optional finisher
Attaching the
finisher plate
and guide rail
1
Line up the thumbscrews on the
finisher plate with the two holes on
the right side of the printer.
Be sure to orient the plate so that
it does not cover the socket
directly above it.
2
Secure the finisher plate to the
printer using the thumbscrews.
3
Orient the holding plate with the
screws as shown.
4
Slide the bottom lip under the
printer.
5
Pull the holding plate upward to
align the thumbscrews in the plate
with the holes in the side of the
printer.
6
Secure the holding plate to the
printer using the thumbscrews.
7
Align the thumbscrews on the
guide rail with the holes in the
holding plate and start the
thumbscrews, but do not tighten
them.
8
Align the top of the guide rail with
the line on the holding plate by
rotating the two alignment knobs
closest to the holding plate. This
action raises or lowers the guide
rail, depending on which way the
knobs are turned.
The edge of the guide rail should
line up with the sticker where the
white and gray portions divide.
9
Secure the guide rail to the
holding plate by tightening the
thumbscrews.
Guide rail
holding plate
Finisher plate
Guide rail
Alignment knobs
Sticker