NEC NP-P502WL Users Manual - Page 135

(4) Attaching the Optional Cable Cover (NP08CV), Attaching the cable cover

Get NEC NP-P502WL PDF manuals and user guides View all NEC NP-P502WL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 135 highlights

❹ Attaching the Optional Cable Cover (NP08CV) After finishing connections, attach the supplied cable cover to properly hide the cables. 9. Appendix CAUTION: • Be sure to tighten the screws after attaching the cable cover. Failure to do so may cause the cable cover to come off and fall, resulting in injury or damage to the cable cover. • Do not put bundled cables in the cable cover. Doing so may damage the power cord, resulting in a fire. • Do not hold the cable cover while moving the projector or do not apply excessive force to the cable cover. Doing so may damage the cable cover, resulting in injury. Attaching the cable cover Tool needed: • Phillips screwdriver (plus-head) about 9 cm/4 inches in length 9 cm/4 inches 1. Align two claws on the cable cover edge with grooves of * As seen from below. the projector and push the top end. 1 • The remaining claw on the cable cover also goes in the Claw on the cable cover projector's groove. edge NOTE: • Be careful not to get cables caught in between the cable cover and the projector. Groove in back panel Cable cover claw 2 2. Tighten the cable cover screws. • Be sure to tighten the screws. 122

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
122
9. Appendix
❹
Attaching the Optional Cable Cover (NP08CV)
After finishing connections, attach the supplied cable cover to properly hide the cables.
CAUTION:
• Be sure to tighten the screws after attaching the cable cover. Failure to do so may cause the cable cover to come
off and fall, resulting in injury or damage to the cable cover.
• Do not put bundled cables in the cable cover.Doing so may damage the power cord, resulting in a fire.
• Do not hold the cable cover while moving the projector or do not apply excessive force to the cable cover.Doing
so may damage the cable cover, resulting in injury.
Attaching the cable cover
Tool needed:
• Phillips screwdriver (plus-head) about 9 cm/4 inches in length
9 cm/4 inches
1. Align two claws on the cable cover edge with grooves of
the projector and push the top end.
•
The remaining claw on the cable cover also goes in the
projector’s groove.
NOTE:
• Be careful not to get cables caught in between the cable cover and
the projector.
1
2
* As seen from below.
Claw on the cable cover
edge
Groove in back
panel
Cable cover
claw
2. Tighten the cable cover screws.
•
Be sure to tighten the screws.