Home » Netgear Manuals » Bridges & Routers » Netgear R6400 » Manual Viewer

Netgear R6400 User Manual - Page 167

Troubleshoot with the LEDs, Standard LED Behavior When the Router Is Powered

Add to My Manuals
Save this manual to your list of manuals

Page 167 highlights

AC1750 Smart WiFi Router Troubleshoot with the LEDs By default, the router is set with standard LED settings. If you disabled blinking for the LEDs or turned off all LEDs except the Power LED, you must return the LEDs to their standard settings for troubleshooting. For information about controlling the LED settings, see Disable LED Blinking or Turn Off LEDs on page 107. Standard LED Behavior When the Router Is Powered On After you turn on power to the router, verify that the following sequence of events occurs: 1. When power is first applied, verify that the Power LED is lit. 2. After approximately 2 minutes, verify the following: • The Power LED is solid white. • The Internet LED is lit. • The WiFi LED is lit unless you turned off the wireless radio. You can use the LEDs on the front panel of the router for troubleshooting. Power LED Is Off or Blinking Do the following: • Make sure that the power adapter is securely connected to your router and securely connected to a working power outlet. • Check that you are using the power adapter that NETGEAR supplied for this product. • If the Power LED blinks slowly and continuously, the router firmware is corrupted. This can happen if a firmware upgrade is interrupted, or if the router detects a problem with the firmware. If the error persists, this indicates a hardware problem. For recovery instructions, or help with a hardware problem, contact technical support at www.netgear.com/support. Power LED Stays Amber When the router is turned on, the Power LED lights amber for about 2 minutes and then turns white. If the LED does not turn white, a problem occurred in the router. If the Power LED is still amber one minute after you turn on power to the router, do the following: 1. Turn off the power and then turn it back on to see if the router recovers. 2. Press and hold the Reset button to return the router to its factory settings. See Troubleshoot Your Network Using the Ping Utility on page 175. If the error persists, a hardware problem might be the cause. Contact technical support at www.netgear.com/support. Troubleshooting 170

Section	Page
AC1750 Smart WiFi Router	1
Contents	3
1. Hardware Setup	8
Unpack Your Router	9
Extend the Antennas	9
Top and Front Panels	10
Rear Panel	11
Position Your Router	11
Cable Your Router	13
2. Connect to the Network and Access the Router	14
Connect to the Network	15
Wired Connection	15
WiFi Connection	15
Label	16
Types of Logins	16
Use an Internet Browser to Access the Router	16
NETGEAR genie Automatic Internet Setup	16
Log In to the Router	19
Change the Language	19
Access the Router with the NETGEAR genie App	20
3. Specify Your Internet Settings	21
Use the Internet Setup Wizard	22
Manually Set Up the Internet Connection	23
Specify an Internet Connection That Does Not Use a Login	23
Specify an Internet Connection That Uses a Login	25
Specify IPv6 Internet Connections	27
Requirements for Entering IPv6 Addresses	28
Use Auto Detect for an IPv6 Internet Connection	28
Use Auto Config for an IPV6 Internet Connection	29
Set Up an IPv6 6rd Tunnel Internet Connection	31
Set Up an IPv6 6to4 Tunnel Internet Connection	33
Set Up an IPv6 Pass Through Internet Connection	35
Set Up an IPv6 Fixed Internet Connection	35
Set Up an IPv6 DHCP Internet Connection	37
Set Up an IPv6 PPPoE Internet Connection	38
Change the MTU Size	40
Enable the Bridge or Add a VLAN Tag Group	42
Enable the Bridge	42
Add VLAN Tag Groups	43
4. Optimize Performance	45
Prioritize Internet Traffic with Quality of Service	46
Optimize Internet Gaming with Upstream QoS	46
Add Upstream QoS Rules	47
Set Up QoS for Applications and Online Gaming	48
Set Up QoS for a Router LAN Port	49
Set Up QoS for a MAC Address	50
Edit an Upstream QoS Policy	51
Delete an Upstream QoS Policy	52
Optimize Video Streaming with Downstream QoS	53
Add Downstream QoS Rules by Keyword	54
Add a Downstream QoS Rule by Device	55
Improve Network Connections with Universal Plug and Play	55
Wi-Fi Multimedia Quality of Service	56
5. Control Access to the Internet	58
Set Up Parental Controls	59
Block Access to Your Network	60
Use Keywords to Block Internet Sites	61
Delete Keywords from the List to Be Blocked	62
Block Services from the Internet	62
Schedule When to Block Internet Sites and Services	64
Avoid Blocking on a Trusted Computer	65
Set Up Security Event Email Notifications	65
6. Share USB Storage Devices Attached to the Router	67
USB Storage Device Requirements	68
Access a USB Storage Device on the Network	69
Back Up Windows Computers with ReadySHARE Vault	72
Back Up Mac Computers with Time Machine	72
Set Up a USB Hard Drive on a Mac	72
Prepare to Back Up a Large Amount of Data	73
Use Time Machine to Back Up onto a USB Hard Drive	73
Control Access to the USB Drive	74
Use FTP Within the Network	77
View or Change Network Folders on a USB Drive	77
Add a Network Folder on a USB Drive	79
Edit a Network Folder on a USB Drive	80
Safely Remove a USB Drive	81
7. Access the Router’s USB Drive Through the Internet	83
Access the USB Drive Through the Internet	84
Set Up FTP Access Through the Internet	84
Access the USB Drive Through the Internet with FTP	85
Dynamic DNS	86
Your Personal FTP Server	86
Set Up a New Dynamic DNS Account	87
Specify a DNS Account	88
Change the Dynamic DNS Settings	90
Set Up Your Personal FTP Server	90
8. Use the Router as a Media Server	91
Specify ReadyDLNA Media Server Settings	92
Play Music from a USB Drive with iTunes Server	92
Play Media from a USB Drive on TiVo	94
9. Share a USB Printer	97
Install the Printer Driver and Cable the Printer	98
Download the ReadySHARE Printer Utility	98
Install the ReadySHARE Printer Utility	99
Use the Shared Printer	100
View or Change the Status of a Printer	101
Use the Scan Feature of a Multifunction USB Printer	102
Change NETGEAR USB Control Center Settings	102
10. Specify Network Settings	104
Disable LED Blinking or Turn Off LEDs	105
View the WAN Settings	105
Set Up a Default DMZ Server	107
Change the Router’s Device Name	108
Change the LAN TCP/IP Settings	108
Specify the IP Addresses That the Router Assigns	110
Disable the DHCP Server Feature in the Router	111
Manage Reserves LAN IP Addresses	112
Reserve an IP Address	112
Edit a Reserved IP Address Entry	113
Delete a Reserved IP Address Entry	113
Use the WPS Wizard for WiFi Connections	114
Specify Basic WiFi Settings	115
Change the WiFi Security Option	117
Set Up a Guest Network	118
How the Router Manages WiFi Clients	120
Airtime Fairness	120
Implicit Beamforming	120
Control the Wireless Radios	121
Use the WiFi On/Off Button	121
Enable or Disable the Wireless Radios	121
Set Up a Wireless Schedule	122
Specify WPS Settings	123
Set Up the Router with an Existing Router or Gateway	124
Use the Router as a Wireless Access Point	126
Set Up the Router in Bridge Mode	127
11. Manage Your Network	130
Update the Router Firmware	131
Change the admin Password	131
Recover the admin Password	132
View Router Status	134
Display Internet Port Statistics	134
Check the Internet Connection Status	135
View and Manage Logs of Router Activity	137
Monitor Internet Traffic	138
Create Custom Static Routes	139
Set Up a Static Route	140
Edit a Static Route	141
Delete a Static Route	141
View Devices Currently on the Network	142
Manage the Router Configuration File	143
Back Up Settings	143
Restore Configuration Settings	144
Erase the Current Configuration Settings	144
Remote Management	145
Remotely Access Your Router Using the genie App	146
12. Use VPN to Access Your Network	147
Set Up a VPN Connection	148
Specify VPN Service in the Router	149
Install OpenVPN Software on Your Computer	149
Use a VPN Tunnel	151
Use VPN to Access the Router’s USB Drive and Media	153
Use VPN to Access Your Internet Service at Home	153
Set Up VPN Client Internet Access in the Router	153
Block VPN Client Internet Access in the Router	154
Use a VPN Tunnel to Access Your Internet Service at Home	155
13. Specify Internet Port Settings	156
Set Up Port Forwarding to a Local Server	157
Add a Custom Port Forwarding Service	158
Edit a Port Forwarding Service	159
Delete a Port Forwarding Entry	159
Application Example: Make a Local Web Server Public	160
How the Router Implements the Port Forwarding Rule	160
Set Up Port Triggering	161
Add a Port Triggering Service	161
Enable Port Triggering	162
Application Example: Port Triggering for Internet Relay Chat	163
14. Troubleshooting	165
Quick Tips	166
Sequence to Restart Your Network	166
Check Ethernet Cable Connections	166
Wireless Settings	166
Network Settings	166
Troubleshoot with the LEDs	167
Standard LED Behavior When the Router Is Powered On	167
Power LED Is Off or Blinking	167
Power LED Stays Amber	167
LEDs Never Turn Off	168
Internet or Ethernet Port LEDs Are Off	168
WiFi LED Is Off	168
Cannot Log In to the Router	168
Cannot Access the Internet	169
Troubleshoot PPPoE	170
Troubleshoot Internet Browsing	171
Changes Not Saved	171
Wireless Connectivity	172
Troubleshoot Your Network Using the Ping Utility	172
Test the LAN Path to Your Router	172
Test the Path from Your Computer to a Remote Device	173
A. Supplemental Information	175
Factory Settings	176

Match case Limit results 1 per page

Troubleshooting

170

AC1750

Smart

WiFi

Router

Troubleshoot with the LEDs

By default, the router is set with standard LED settings. If you disabled blinking for the LEDs

or turned off all LEDs except the Power LED, you must return the LEDs to their standard

settings for troubleshooting. For information about controlling the LED settings, see

Disable

LED Blinking or Turn Off LEDs

on page

107.

Standard LED Behavior When the Router Is Powered On

After you turn on power to the router, verify that the following sequence of events occurs:

When power is first applied, verify that the Power LED

is lit.

After approximately 2 minutes, verify the following:

•

The Power LED is solid white.

•

The Internet LED is lit.

•

The WiFi LED is lit unless you turned off the wireless radio.

You can use the LEDs on the front panel of the router for troubleshooting.

Power LED Is Off or Blinking

Do the following:

•

Make sure that the power adapter is securely connected to your router and securely

connected to a working power outlet.

•

Check that you are using the power adapter that NETGEAR supplied for this product.

•

If the Power LED blinks slowly and continuously, the router firmware is corrupted. This

can happen if a firmware upgrade is interrupted, or if the router detects a problem with the

firmware. If the error persists, this indicates a hardware problem. For recovery

instructions, or help with a hardware problem, contact technical support at

www.netgear.com/support.

Power LED Stays Amber

When the router is turned on, the Power LED lights amber for about 2 minutes and then turns

white. If the LED does not turn white, a problem occurred in the router.

If the Power LED is still amber one minute after you turn on power to the router, do the

following:

Turn off the power and then turn it back on to see if the router recovers.

Press and hold the

Reset

button to return the router to its factory settings.

See

Troubleshoot Your Network Using the Ping Utility

on page

175.

If the error persists, a hardware problem might be the cause. Contact technical support at