Netgear WN802Tv2 Reference Manual - Page 78

Troubleshooting, No lights are lit on the access point., The Ethernet light is not lit. - antenna power

Get Netgear WN802Tv2 - Wireless-N Access Point PDF manuals and user guides
UPC - 606449058505
View all Netgear WN802Tv2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

NETGEAR Wireless-N Access Point WN802T v2 Reference Manual Troubleshooting Following are some simple problems that could occur and their possible causes. Along with each problem description, instructions are provided to assist you in diagnosing and solving the problem. No lights are lit on the access point. The access point has no power. • Make sure the power cord is connected to the access point and plugged in to a working power outlet or power strip. • Make sure you are using the correct NETGEAR power adapter supplied with your access point; in this case the Switching Power Supply. The Ethernet light is not lit. There is a hardware connection problem. • Make sure the cable connectors are securely plugged in at the wireless access point and the network device (hub, switch, or router). • Make sure the connected device is turned on. The WLAN light is not lit. The wireless access point built-in antennas are not functioning properly. • Select the "Turn Radio On" radio button setting on the Wireless Settings screen under Wireless > Advanced. It must be turned on (selected). See Figure 6-1 • If the Wireless LAN activity light stays off, disconnect the adapter from its power source and then plug it in again. 6-2 Troubleshooting and Help v1.0, September 2008

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
NETGEAR Wireless-N Access Point WN802T v2 Reference Manual
6-2
Troubleshooting and Help
v1.0, September 2008
Troubleshooting
Following are some simple problems that could occur and their possible causes. Along with each
problem description, instructions are provided to assist you in diagnosing and solving the problem.
No lights are lit on the access point.
The access point has no power.
•
Make sure the power cord is connected to the access point and plugged in to a working power
outlet or power strip.
•
Make sure you are using the correct NETGEAR power adapter supplied with your access
point; in this case the Switching Power Supply.
The Ethernet light is not lit.
There is a hardware connection problem.
•
Make sure the cable connectors are securely plugged in at the wireless access point and the
network device (hub, switch, or router).
•
Make sure the connected device is turned on.
The WLAN light is not lit.
The wireless access point built-in antennas are not functioning properly.
•
Select the “
Turn Radio On
” radio button setting on the Wireless Settings
screen under
Wireless > Advanced
. It must be turned on (selected). See
Figure 6-1
•
If the Wireless LAN activity light stays off, disconnect the adapter from its power source and
then plug it in again.