Onkyo TX-RZ50 9.2-Channel THX Certified AV Receiver Instruction Manual - Engli - Page 132

Speaker Impedance Default Value: 6 ohms or above, Height 2 Speaker Default Value: Rear High

Get Onkyo TX-RZ50 9.2-Channel THX Certified AV Receiver PDF manuals and user guides View all Onkyo TX-RZ50 9.2-Channel THX Certified AV Receiver manuals
Add to My Manuals
Save this manual to your list of manuals

Page 132 highlights

2. Speaker ‰‰Height 2 Speaker (Default Value: Rear High) Set the speaker type if height speakers are connected to the HEIGHT 2 terminals. Select "Front High", "Top Front", "Top Middle", "Top Rear", "Rear High", "Dolby Speaker (Front)" or "Dolby Speaker (Surr)" according to the type and layout of the connected speakers. However, the options selectable for the "Height 1 Speaker" are as follows. -- If "Height 1 Speaker" is set to "Front High": Select from "Top Middle", "Top Rear", "Rear High" or "Dolby Speaker (Surr)". -- If "Height 1 Speaker" is set to "Top Front" or "Dolby Speaker (Front)": Select from "Top Rear", "Rear High" or "Dolby Speaker (Surr)". -- If "Height 1 Speaker" is set to "Top Middle": Fixed to "Rear High". • "Dolby Speaker (Surr)" can only be selected when surround speakers are being used. You can check speakers that you are using on the figure displayed in "Speaker Channels". • If an item cannot be selected even though connection is correct, check that the settings in "Speaker Channels" matches the number of connected channels. ‰‰Zone Speaker (Default Value: No) Set the connection of speakers to Zone 2 or Zone 3 speaker terminals. • This setting cannot be selected when "Zone 2 Preout" is set to "Zone B". Zone 2 When speakers are connected to Zone 2 speaker terminals Zone 2/Zone 3 When connecting speakers to both ZONE 2 speaker terminals and ZONE 3 speaker terminals. • This setting cannot be selected under any of following conditions. -- When the surround back speakers are used -- When 2 sets of height speakers are used No When speakers are not connected to neither ZONE 2 nor ZONE 3 speaker terminals Setup ‰‰Zone 2 Preout (Default Value: Zone 2) Set an output destination of the audio output from ZONE 2 PRE/LINE OUT/ ZONE B LINE OUT jack. • This setting is fixed to "Zone 2" when "Zone Speaker" is set to "Zone 2" or "Zone 2/Zone 3". Zone 2 Zone B When connecting an integrated amplifier in a separate room (ZONE 2) When connecting an integrated amplifier, transmitter of wireless headphones, etc. to ZONE B ‰‰Bi-Amp (Default Value: No) Set whether the front speakers are bi-amp connected. No When front speakers are not bi-amp connected Yes When front speakers are bi-amp connected • This setting will be set to "No" in either of following cases. -- When 2 sets of height speakers are used -- When surround back speakers and height speakers are being used at the same time. -- When "Zone Speaker" is set to "Zone 2" or "Zone 2/Zone 3" ‰‰Speaker Impedance (Default Value: 6 ohms or above) Set the impedance (Ω) of the connected speakers. • For impedance, check the indications on the back of the speakers or their instruction manual. 4ohms When any of the connected speakers have 4 Ω or more to less than 6 Ω impedance 6 ohms or above When all the connected speakers have an impedance of 6 Ω or more 132

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
132
Setup
Setup
2. Speaker
±
Height 2 Speaker (Default Value: Rear High)
Set the speaker type if height speakers are connected to the HEIGHT 2
terminals.
Select "Front High", "Top Front", "Top Middle", "Top Rear", "Rear High", "Dolby
Speaker (Front)" or "Dolby Speaker (Surr)" according to the type and layout
of the connected speakers. However, the options selectable for the "Height 1
Speaker" are as follows.
– If "Height 1 Speaker" is set to "Front High": Select from "Top Middle", "Top
Rear", "Rear High" or "Dolby Speaker (Surr)".
– If "Height 1 Speaker" is set to "Top Front" or "Dolby Speaker (Front)":
Select from "Top Rear", "Rear High" or "Dolby Speaker (Surr)".
– If "Height 1 Speaker" is set to "Top Middle": Fixed to "Rear High".
•
"Dolby Speaker (Surr)" can only be selected when surround speakers
are being used. You can check speakers that you are using on the figure
displayed in "Speaker Channels".
•
If an item cannot be selected even though connection is correct, check
that the settings in "Speaker Channels" matches the number of connected
channels.
±
Zone Speaker (Default Value: No)
Set the connection of speakers to Zone 2 or Zone 3 speaker terminals.
•
This setting cannot be selected when "Zone 2 Preout" is set to "Zone B".
Zone 2
When speakers are connected to Zone 2 speaker terminals
Zone 2/Zone 3
When connecting speakers to both ZONE 2 speaker terminals
and ZONE 3 speaker terminals.
•
This setting cannot be selected under any of following
conditions.
– When the surround back speakers are used
– When 2 sets of height speakers are used
No
When speakers are not connected to neither ZONE 2 nor
ZONE 3 speaker terminals
±
Zone 2 Preout (Default Value: Zone 2)
Set an output destination of the audio output from ZONE 2 PRE/LINE OUT/
ZONE B LINE OUT jack.
• This setting is fixed to "Zone 2" when "Zone Speaker" is set to "Zone 2"
or
"Zone 2/Zone 3".
Zone 2
When connecting an integrated amplifier in a separate room
(ZONE 2)
Zone B
When connecting an integrated amplifier, transmitter of
wireless headphones, etc. to ZONE B
±
Bi-Amp (Default Value: No)
Set whether the front speakers are bi-amp connected.
No
When front speakers are not bi-amp connected
Yes
When front speakers are bi-amp connected
•
This setting will be set to "No" in either of following cases.
– When 2 sets of height speakers are used
– When surround back speakers and height speakers are
being used at the same time.
– When "Zone Speaker" is set to "Zone 2" or "Zone 2/Zone
3"
±
Speaker Impedance (Default Value: 6 ohms or above)
Set the impedance (Ω) of the connected speakers.
•
For impedance, check the indications on the back of the speakers or their
instruction manual.
4ohms
When any of the connected speakers have 4 Ω or more to less
than 6 Ω impedance
6 ohms or above
When all the connected speakers have an impedance of 6 Ω
or more