Onkyo TX-RZ50 9.2-Channel THX Certified AV Receiver Instruction Manual - Engli - Page 133

Crossover, Surround Back Default Value: 80 Hz THX

Get Onkyo TX-RZ50 9.2-Channel THX Certified AV Receiver PDF manuals and user guides View all Onkyo TX-RZ50 9.2-Channel THX Certified AV Receiver manuals
Add to My Manuals
Save this manual to your list of manuals

Page 133 highlights

2. Speaker „„2. Crossover Change the settings of crossover frequencies. ‰‰Front (Default Value: 80 Hz (THX)) Center (Default Value: 80 Hz (THX)) Height 1 (Default Value: 80 Hz (THX)) Height 2 (Default Value: 80 Hz (THX)) Surround (Default Value: 80 Hz (THX)) Surround Back (Default Value: 80 Hz (THX)) LPF of LFE (Default Value: 120 Hz) Double Bass (Default Value: On) • As for the THX-certified speakers, the following settings are recommended. -- Crossover frequency → "80 Hz(THX)" -- "LPF of LFE" → "80 Hz" -- "Double Bass" → "Off" • This setting is disabled when the IMAX sound mode has been applied. However, when the "IMAX User Setting" ( →p139) is "Manual" (default value is Auto), it is enabled. Front: Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • If "Configuration" - "Subwoofer" is set to "No", "Front" is fixed to "Full Band", and the low pitched range of the other channels is output from the front speakers. Refer to the instruction manual of your speakers to make the setting. Center, Height 1, Height 2, Surround: Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band". • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels. Setup Surround Back: Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Surround" is set to "Full Band". • If the item cannot be selected even though connection is correct, check if the setting in "Configuration" - "Speaker Channels" matches the number of connected channels. LPF of LFE: Set the low-pass filter for LFE (low-frequency effect) signals in order to pass only the lower frequency signals than the set value, and thus cancel unwanted noises. The low-pass filter is effective only on sources with LFE channel. The value from "80 Hz" to "120 Hz" can be set. "Off": When this function is not used Double Bass: This can be selected only when "Configuration" - "Subwoofer" is set to "Yes" and "Front" is set to "Full Band". Boost bass output by feeding bass sounds from the front left and right speakers and the center speaker to the subwoofer. "On": Bass output is boosted. "Off": Bass output is not boosted. • This function is not automatically set even if AccuEQ Room Calibration or Dirac Live is performed. 133

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
133
Setup
Setup
2. Speaker
±
2. Crossover
Change the settings of crossover frequencies.
±
Front
(Default Value: 80 Hz (THX))
Center
(Default Value: 80 Hz (THX))
Height 1
(Default Value: 80 Hz (THX))
Height 2
(Default Value: 80 Hz (THX))
Surround
(Default Value: 80 Hz (THX))
Surround Back (Default Value: 80 Hz (THX))
LPF of LFE
(Default Value: 120 Hz)
Double Bass
(Default Value: On)
• As for the THX-certified speakers, the following settings are recommended.
–
Crossover frequency → "80 Hz(THX)"
–
"LPF of LFE" → "80 Hz"
–
"Double Bass" → "Off"
•
This setting is disabled when the IMAX sound mode has been applied.
However, when the "IMAX User Setting" (
→
p139
) is "Manual" (default value
is Auto), it is enabled.
Front:
Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting
frequencies for each channel.
"Full Band": Full band will be output.
• If "Configuration" - "Subwoofer" is set to "No", "Front" is fixed to "Full Band",
and the low pitched range of the other channels is output from the front
speakers. Refer to the instruction manual of your speakers to make the
setting.
Center, Height 1, Height 2, Surround:
Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting
frequencies for each channel.
"Full Band": Full band will be output.
•
"Full Band" can be selected only when "Front" is set to "Full Band".
•
If the item cannot be selected even though connection is correct, check if
the setting in "Configuration" - "Speaker Channels" matches the number of
connected channels.
Surround Back:
Select the crossover frequency from "40 Hz" to "200 Hz" to start outputting
frequencies for each channel.
"Full Band": Full band will be output.
•
"Full Band" can be selected only when "Surround" is set to "Full Band".
•
If the item cannot be selected even though connection is correct, check if
the setting in "Configuration" - "Speaker Channels" matches the number of
connected channels.
LPF of LFE:
Set the low-pass filter for LFE (low-frequency effect) signals in order to pass
only the lower frequency signals than the set value, and thus cancel unwanted
noises. The low-pass filter is effective only on sources with LFE channel.
The value from "80 Hz" to "120 Hz" can be set.
"Off": When this function is not used
Double Bass:
This can be selected only when "Configuration" - "Subwoofer" is set to "Yes"
and "Front" is set to "Full Band".
Boost bass output by feeding bass sounds from the front left and right
speakers and the center speaker to the subwoofer.
"On": Bass output is boosted.
"Off": Bass output is not boosted.
•
This function is not automatically set even if AccuEQ Room Calibration or
Dirac Live is performed.