Onkyo TX-RZ50 9.2-Channel THX Certified AV Receiver Instruction Manual - Engli - Page 150

Power Management, Auto Standby in HDMI Standby Through Default Value: On/Off

Get Onkyo TX-RZ50 9.2-Channel THX Certified AV Receiver PDF manuals and user guides View all Onkyo TX-RZ50 9.2-Channel THX Certified AV Receiver manuals
Add to My Manuals
Save this manual to your list of manuals

Page 150 highlights

5. Hardware „„4. Power Management Change the settings for the power-save function. ‰‰Sleep Timer (Default Value: Off) 30 minutes, 60 minutes, 90 minutes Off You can allow the unit to enter standby automatically when the specified time has elapsed. Select a value from "30 minutes", "60 minutes" and "90 minutes". Does not turn the unit to standby automatically. ‰‰Auto Standby (Default Value: On/Off) This setting allows the unit to enter standby mode automatically after 20 minutes of inactivity without any video or audio input. (When "USB Power Out at Standby" or "Network Standby" is enabled, the unit enters the HYBRID STANDBY mode which minimizes the increase in power consumption.) • Default values vary depending on the regions. On The unit will automatically enter standby mode ("AUTO STBY" will light). • "Auto Standby" is displayed on the main unit's display and TV screen 30 seconds before entering standby mode. • "Auto Standby" does not work when Zone 2/Zone 3 is active. Off The unit will not automatically enter standby mode. ‰‰Auto Standby in HDMI Standby Through (Default Value: On/Off) Enable or disable "Auto Standby" while "HDMI Standby Through" is on. • Default values vary depending on the regions. On The setting will be enabled. • This setting cannot be set to "On" if "Auto Standby" and "HDMI Standby Through" are set to "Off". Off The setting will be disabled. Setup ‰‰USB Power Out at Standby (Default Value: Off) Devices connected to the USB port (5 V/1 A) on the rear of the unit can be supplied with electricity even when this unit is in standby mode when this function is "On". • When this function is set to "On", the power consumption in standby state increases, however, the increase in power consumption is minimized by automatically entering the HYBRID STANDBY mode where only the essential circuits operate. ‰‰Network Standby (Default Value: On) When this function is set to "On", the network function works even in standby state, and you can turn on the power of the unit via network using an application such as Onkyo Controller that can control this unit. • When this function is set to "On", the power consumption in standby state increases, however, the increase in power consumption is minimized by automatically entering the HYBRID STANDBY mode where only the essential circuits operate. Note that even if this function is set to "Off", when any of the HDMI CEC ( →p143), HDMI Standby Through ( →p143), USB Power Out at Standby ( →p150) and Bluetooth Wakeup ( →p151) functions is enabled, this function will be in "On" state regardless of the setting. • When connection to the network is lost, "Network Standby" may be disabled to reduce power consumption. In such a case, turn the unit on by using the power button on the remote controller or main unit. 150

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
150
Setup
Setup
5. Hardware
±
4. Power Management
Change the settings for the power-save function.
±
Sleep Timer (Default Value: Off)
30 minutes,
60 minutes,
90 minutes
You can allow the unit to enter standby automatically when the
specified time has elapsed. Select a value from "30 minutes",
"60 minutes" and "90 minutes".
Off
Does not turn the unit to standby automatically.
±
Auto Standby (Default Value: On/Off)
This setting allows the unit to enter standby mode automatically after 20
minutes of inactivity without any video or audio input. (When "USB Power Out
at Standby" or "Network Standby" is enabled, the unit enters the HYBRID
STANDBY mode which minimizes the increase in power consumption.)
•
Default values vary depending on the regions.
On
The unit will automatically enter standby mode ("AUTO STBY"
will light).
•
"Auto Standby" is displayed on the main unit’s display and
TV screen 30 seconds before entering standby mode.
•
"Auto Standby" does not work when Zone 2/Zone 3 is active.
Off
The unit will not automatically enter standby mode.
±
Auto Standby in HDMI Standby Through (Default Value: On/Off)
Enable or disable "Auto Standby" while "HDMI Standby Through" is on.
•
Default values vary depending on the regions.
On
The setting will be enabled.
•
This setting cannot be set to "On" if "Auto Standby" and
"HDMI Standby Through" are set to "Off".
Off
The setting will be disabled.
±
USB Power Out at Standby (Default Value: Off)
Devices connected to the USB port (5 V/1 A) on the rear of the unit can be
supplied with electricity even when this unit is in standby mode when this
function is "On".
•
When this function is set to "On", the power consumption in standby state
increases, however, the increase in power consumption is minimized
by automatically entering the HYBRID STANDBY mode where only the
essential circuits operate.
±
Network Standby (Default Value: On)
When this function is set to "On", the network function works even in standby
state, and you can turn on the power of the unit via network using an
application such as Onkyo Controller that can control this unit.
•
When this function is set to "On", the power consumption in standby state
increases, however, the increase in power consumption is minimized
by automatically entering the HYBRID STANDBY mode where only the
essential circuits operate. Note that even if this function is set to "Off", when
any of the HDMI CEC (
→
p143
), HDMI Standby Through (
→
p143
),
USB Power Out at Standby (
→
p150
) and Bluetooth Wakeup (
→
p151
)
functions is enabled, this function will be in "On" state regardless of the
setting.
•
When connection to the network is lost, "Network Standby" may be disabled
to reduce power consumption. In such a case, turn the unit on by using the
power button on the remote controller or main unit.