Onkyo TX-SV919 Owner Manual - Page 56
Listening, devices, connected, TX-SV919THX, another
View all Onkyo TX-SV919 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 56 highlights
Listening to devices connected to the TX-SV919THX in another room Multiple Room Remote System (I1T4 Please refer pages 16 and 17 for connection and set-up methods. • TX-SV919THX allows you to listen to the desired performance in another room (sub room) while listening to the Multi source pre out play- back of a device located in the main room. To do this, connect the stereo main amp terminals on the TX-SV919THX. • Connect the Stereo main amplifier to the MULTISOURCE PRE OUT on the TX-SV919THX and connect the speaker cables from the speakers in the other room to the speaker terminals on the Stereo main amplifier. • Remote control from another room can be done by employing the ONKYO multiple room remote system Tin ). Refer to the connections for multiple room remote control. Be sure to operate the remote control unit directing pointing to the remote sensor unit HR-10. • The following steps (except step 1 ) can be performed using the remote control unit. It is recommended that the adjustments described below be done in the main room in advance, since it is not possible to operate the remote control unit in another room while watching the display of the TX-SV919THX. • When using the included remote control unit (RC-267M), set A, B, C Selector switch to C (SUB ROOM). Only the functions related to the Multiple Room Remote system are output. Only buttons on the remote control with a blue line under them can be used. 0 Oc000, CCI OEM CiLil IZECI IMECI MULTI SOURCE 1TR off rrR off indicator POWER SOURCE-, SELECTOR TUNER DECK A,B C 0 0 0 0 0 C C 0 C CD 00 00 00 M0 C C C CO C 0 C C CTS ROOM, Soolcn to Cf SUB ROOMI VOLUME +/- 1. Turn the rrR OFF button off. 111T OFF O indicator off 1:!) IITR OFF 2. Press the MULTI SOURCE button. MULTI SOURCE CD < MULTI SOURCE flash 3. While this is flashing, use the Input Selector button to select the desired source. HIPPO I VIDEO I HIDEO 2j I VIDEO 3 I I VJPEO I VIDEOS I PI I PPFI I TAPES I TUNER i PITONO I I OP 1< j'T j • If the tuner is selected with MULTI SOURCE and the Input Selector is set to something other than TUNER, the tuners frequency and class displays will be shown for 3 seconds. • When changing the source, be sure to press the MULTI SOURCE button before pressing the Input Selector button. Pressing the Input Selector button without first pressing the MULTI SOURCE button will change the source in the main room. • The remote control can be used to perform steps 2 and 3 by first positioning the A/B/C (SUB ROOM) selector switch to the C (SUB ROOM) position and pressing the SOURCE SELECTOR button. 4. Adjust the level using the VOLUME +1- buttons on the remote control. • MULTI SOURCE level will be indicated on the display. It is rec- ommended that the level be set lower in advance in the main room (-78 to -76dB). • Note that before adjusting the level using the VOLUME +/- buttons, set the selector switch on the remote control to the C (SUB ROOM) position. If the position is set to A or B, the MASTER VOLUME affects the speaker volume in the main room, not the sub room. m4 off button OR OFF) and indicator Use this button for tape recording. It is used to disable control of the ONKYO ITTR system via the remote control in another room. Pressing this button will illuminate the indicator, and control from another room will be disabled. Pressing the button again will turn the indicator off, and control from the other room will be enabled. 56 • The source indicated by the Input Selector will be output from the TAPE-1 and 2, and VIDEO-1, -2 and 3 REC OUT terminals. • If the multi source is selected, ITR OFF will automatically be deactivated. • If the multi source is selected for REC OUT, ITR OFF will automatically be activated.