Panasonic 50LCX63 Multi-media Display - Page 8

Emergency Alert System EAS Forced Tuning, Remote Control Battery Installation, Helpful Hints

Get Panasonic 50LCX63 - PT - 50inch Rear Projection TV PDF manuals and user guides View all Panasonic 50LCX63 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Before Using Remote Control Battery Installation Requires two AA batteries (supplied). 1. While pressing in on the catch, open cover in direction of arrow. 2. Install the batteries as shown in the battery compartment. (Polarity + or - must match the markings in the compartment). 3. Press cover in direction of arrow until it snaps shut. Two AA size CAUTION Incorrect battery installation can cause the batteries to leak, leading to personal injury and/or damage to the remote control. Observe the following precautions: 1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. 2. Do not mix battery types (example: "Zinc Carbon" with "Alkaline"). 3. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. 4. Battery replacement is necessary when the remote control acts sporadically or stops operating the Device Display set. Helpful Hints: (1) For frequent remote control users, replace old batteries with Alkaline batteries for longer battery life. (2) Whenever you remove the batteries, you may need to reset the remote control infrared codes. We recommend that you record the code on page 90, prior to setting up the remote. Emergency Alert System (EAS) Forced Tuning If a DCM (Digital Cable Module) is installed, the cable MSO (multiple system owner/operator) may provide an Emergency Alert System message. These messages are intended to alert the general public of important local or national emergency situations. In the event of receipt of one of these messages, the Device Display shall immediately tune to the channel as directed by the EAS message. If the channel has been blocked using the parental control, the parental blocking has priority over the forced tune. 8 For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
8
For assistance, please call : 1-888-VIEW PTV(843-9788) or, contact us via the web at: http://www.panasonic.com/contactinfo
Before Using
Emergency Alert System (EAS) Forced Tuning
If a DCM (Digital Cable Module) is installed, the cable
MSO (multiple system owner/operator) may provide
an Emergency Alert System message. These messages are intended to alert the general public of important
local or national emergency situations. In the event of receipt of one of these messages, the Device Display
shall immediately tune to the channel as directed by the EAS message. If the channel has been blocked
using the parental control, the parental blocking has priority over the forced tune.
Requires two AA batteries (supplied).
2.
Install the batteries as shown in
the battery compartment.
(Polarity + or - must match the
markings in the compartment).
Two AA size
Remote Control Battery Installation
CAUTION
1.
While pressing in on the catch,
open cover in direction of arrow.
3.
Press cover in direction of
arrow until it snaps shut.
Incorrect battery installation can cause the batteries to leak, leading to personal injury and/or damage to the remote
control.
Observe the following precautions:
1.
Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.
2.
Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).
3.
Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.
4.
Battery replacement is necessary when the remote control acts sporadically or stops operating the Device
Display set.
Helpful Hints:
(1) For frequent remote control users, replace old batteries with Alkaline batteries for longer battery life.
(2) Whenever you remove the batteries,
you may need to reset the remote control infrared codes.
We
recommend that you record the code on page 90, prior to setting up the remote.