Panasonic AJSD755 AJSD755 User Guide - Page 18

JOG / SHUTTLE, Jog mode, Shuttle mode

Page 18 highlights

Jog/Shuttle Jog mode Shuttle mode 1 Press the search dial so that it remains pressed in. Check that the JOG lamp has lighted. 2 Turn the search dial. The dial's click-stops are released, and the tape is played back at the speed (-1a to +1a) corresponding to the speed at which the dial is turned. The maximum speed can be switched using setup menu No. 323 (JOG FWD MAX) and No. 324 (JOG REV MAX) settings. However, noise will occur at all speeds other than -0.43a to +0.43a. When the dial is no longer turned, the still picture mode is established. 3 To transfer the VTR from the jog mode to another mode, press the button that corresponds to the mode concerned. The direct search mode in which the VTR is transferred to the shuttle mode or jog mode by turning the search dial is set at the factory. By selecting KEY as the setup menu No. 100 (SEARCH ENA) setting, the VTR can be set to the mode in which it will not be transferred to the search mode unless the search button is pressed. 1 Press the search dial so that it is released from the pressed-in position. The SHTL lamp lights, and the shuttle mode is established. OImmediately after the power is turned on, turn the search dial and leave it at the center position. 2 Press the SHTL/SLOW button and switch to SHTL or SLOW. 3 Turn the search dial. OWhen the SHTL lamp among the JOG, SHTL and SLOW lamps is lighted, the playback picture speed changes from 0 up to ±32a depending on the dial position. This speed can be switched to ±8.4a, ±16a or ±32a using setup menu No. 101 (SHTL MAX). The dial has a click-stop at the center position where the still picture mode is established. OWhen the SLOW lamp among the JOG, SHTL and SLOW lamps is lighted, the playback picture speed changes from -4.1 up to +4.1a depending on the dial position. The maximum speed can be switched using setup menu No. 320 (VAR FWD MAX) and No. 321 (VAR REV MAX) settings. However, noise will occur at all speeds other than -0.43a to +0.43a, +0.5a and +0.75a. The dial has a click-stop at the center position where the still picture mode is established. 4 To transfer the VTR from the shuttle mode to another mode, press the STOP button or other button. O It is possible to listen to playback audio in the -10 to +10 speed range from the audio monitor output. (PCM must be selected for the setup menu No. 721 (MONI CH SELECT) setting.) OThe audio playback sound heard in the search mode contains noise. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78

18
Jog mode
Jog/Shuttle
1
Press the search dial so that it remains pressed in.
Check that the JOG lamp has lighted.
Shuttle mode
1
Press the search dial so that it is released from the
pressed-in position.
The SHTL lamp lights, and the shuttle mode is
established.
O
Immediately after the power is turned on, turn
the search dial and leave it at the center
position.
3
To transfer the VTR from the jog mode to another
mode, press the button that corresponds to the
mode concerned.
2
Turn the search dial.
The dial
s click-stops are released, and the tape is
played back at the speed (
1
a
to +1
a
)
corresponding to the speed at which the dial is
turned.
The maximum speed can be switched using setup
menu No. 323 (JOG FWD MAX) and No. 324 (JOG
REV MAX) settings.
However, noise will occur at all speeds other than
0.43
a
to +0.43
a
.
When the dial is no longer turned, the still picture
mode is established.
3
Turn the search dial.
O
When the SHTL lamp among the JOG, SHTL
and SLOW lamps is lighted, the playback picture
speed changes from 0 up to ±32
a
depending on
the dial position.
This speed can be switched to ±8.4
a
, ±16
a
or
±32
a
using setup menu No. 101 (SHTL MAX).
The dial has a click-stop at the center position
where the still picture mode is established.
O
When the SLOW lamp among the JOG, SHTL
and SLOW lamps is lighted, the playback picture
speed changes from
4.1 up to +4.1
a
depending on the dial position.
The maximum speed can be switched using
setup menu No. 320 (VAR FWD MAX) and No.
321 (VAR REV MAX) settings. However, noise
will occur at all speeds other than
0.43
a
to
+0.43
a
, +0.5
a
and +0.75
a
.
The dial has a click-stop at the center position
where the still picture mode is established.
4
To transfer the VTR from the shuttle mode to
another mode, press the STOP button or other
button.
2
Press the SHTL/SLOW button and switch to SHTL
or SLOW.
<Note>
The direct search mode in which the VTR is
transferred to the shuttle mode or jog mode by turning
the search dial is set at the factory.
By selecting KEY as the setup menu No. 100
(SEARCH ENA) setting, the VTR can be set to the
mode in which it will not be transferred to the search
mode unless the search button is pressed.
<Notes>
O
It is possible to listen to playback audio in the
10
to +10 speed range from the audio monitor output.
(PCM must be selected for the setup menu No. 721
(MONI CH SELECT) setting.)
O
The audio playback sound heard in the search
mode contains noise.