Panasonic AJSD755 AJSD755 User Guide - Page 67

Consult your dealer if the error message is still, displayed even after restarting the unit.

Page 67 highlights

Error messages Error messages Display ODescription OVTR operation and corrective action E-64 S REEL ROTA TOO FAST If the supply reel motor speed is abnormally high, the error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. E-67 T REEL ROTA TOO FAST If the take-up reel motor speed is abnormally high, the error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. E-69 T REEL TORQUE ERR If excess torque being applied to the take-up reel motor is detected, the error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. E-70 S REEL TORQUE ERR If excess torque being applied to the supply reel motor is detected or an abnormal current flowing to the current detection resistor is detected, this error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. E-71 CAP TENSION ERROR If abnormal tension at the supply side is detected in the capstan mode, the error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. E-72 REEL TENSION ERROR If abnormal tension at the supply side is detected in the reel mode, the error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. E-73 REEL DIR UNMATCH If the take-up reel motor has rotated in the reverse direction, this error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. E-74 DRUM TORQUE ERROR If excess torque being applied to the cylinder motor is detected, this error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. E-78 M-IF COMM ERROR If a problem has been encountered in communication between the servo microcomputer and mechanism relay board, this error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. Consult your dealer if the error message is still displayed even after restarting the unit. 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78

67
Error messages
Error messages
Display
O
Description
O
VTR operation and corrective action
E-78
M-IF COMM
ERROR
If a problem has been encountered in
communication
between
the
servo
microcomputer and mechanism relay board, this
error number flashes on the display.
VTR:
STOP
O
Set the POWER switch to OFF and then to
ON again.
E-67
T REEL ROTA
TOO FAST
If the take-up reel motor speed is abnormally
high, the error number flashes on the display.
VTR:
STOP
O
Set the POWER switch to OFF and then to
ON again.
E-64
S REEL ROTA
TOO FAST
If the supply reel motor speed is abnormally
high, the error number flashes on the display.
VTR:
STOP
O
Set the POWER switch to OFF and then to
ON again.
E-69
T REEL
TORQUE ERR
If excess torque being applied to the take-up
reel motor is detected, the error number flashes
on the display.
VTR:
STOP
O
Set the POWER switch to OFF and then to
ON again.
E-70
S REEL
TORQUE ERR
If excess torque being applied to the supply reel
motor is detected or an abnormal current flowing
to the current detection resistor is detected, this
error number flashes on the display.
VTR:
STOP
O
Set the POWER switch to OFF and then to
ON again.
E-71
CAP TENSION
ERROR
If abnormal tension at the supply side is
detected in the capstan mode, the error number
flashes on the display.
VTR:
STOP
O
Set the POWER switch to OFF and then to
ON again.
E-72
REEL
TENSION
ERROR
If abnormal tension at the supply side is
detected in the reel mode, the error number
flashes on the display.
VTR:
STOP
O
Set the POWER switch to OFF and then to
ON again.
E-73
REEL DIR
UNMATCH
If the take-up reel motor has rotated in the
reverse direction, this error number flashes on
the display.
VTR:
STOP
O
Set the POWER switch to OFF and then to
ON again.
E-74
DRUM
TORQUE
ERROR
If excess torque being applied to the cylinder
motor is detected, this error number flashes on
the display.
VTR:
STOP
O
Set the POWER switch to OFF and then to
ON again.
Consult your dealer if the error message is still
displayed even after restarting the unit.