Panasonic AJSD755 AJSD755 User Guide - Page 66

Error messages Error messages Display ODescription OVTR operation and corrective action E-20 DEW If condensation is detected, the error number flashes and the unit transfers to eject mode. The drum rotates after the cassette is ejected to eliminate the condensation. Once the unit is released from condensation status, the error message display is cleared and the VTR is able to be used. OIf condensation is detected in the eject mode, the drum starts rotating as soon as it is detected. OIf condensation is detected when the cassette has been inserted, the drum rotation is stopped, and after the tape is ejected, the drum starts rotating. VTR: EJECT OLeave the power on and wait. E-29 FRONT LOAD MOTOR The unit switches to eject mode and if the cassette fails to move up within 6 seconds, this error number flashes on the display. OIf the cassette does not move down inside the machine even when 6 seconds have elapsed since the cassette was inserted, the VTR is transferred to the eject mode. VTR: STOP OSet the POWER switch to OFF and then to ON again. E-31 LOADING MOTOR If the unloading operation is not completed within 6 seconds, this error number flashes on the display. OWhen the loading operation is not completed within 6 seconds, the VTR is transferred to the eject (unloading) mode. VTR: STOP OSet the POWER switch to OFF and then to ON again. E-35 SERVO CONTROL ERROR If there is no response from the servo microcomputer for 1 second or more, this error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. E-37 If 10 seconds or more elapses and the servo microcomputer has not followed orders issued SERVO COMM by the system control microcomputer, this error ERROR number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. E-38 SERVO FG ERROR If automatic adjustment of the reel and capstan rotation in eject status was not performed correctly when the power was turned on, this error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. Display ODescription OVTR operation and corrective action E-51 FRONT LOAD ERROR E-52 W-UP REEL NOT ROTA E-53 WINDUP ERROR E-55 UNLOAD ERROR E-57 S-FF/REW TIMEOVER E-59 DRUM ROTA TOO SLOW E-60 DRUM ROTA TOO FAST E-61 CAP ROTA TOO SLOW If the take-up reel rotates without engaging for a specific period of time during the start or end processing operation while loading is underway (half position), this error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. If the take-up reel fails to take up the tape while the tape is traveling in the state where the total amount of the tape has not yet been detected after the cassette was inserted, this error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. If there is an abnormally large discrepancy between the amount of tape taken up by the take-up reel and the amount of tape supplied by the supply reel while the tape is traveling after the total amount of the tape begins to be detected, this error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. If the tape has not been taken up during unloading, this error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. If the start or end processing operation is not completed, this error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. If the cylinder motor speed is abnormally low, this error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. If the cylinder motor speed is abnormally high, this error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. If the capstan motor speed is abnormally low, the error number flashes on the display. VTR: STOP OSet the POWER switch to OFF and then to ON again. 66