Panasonic KX-HN1003 HomeHawk App Users Guide - Page 190

Initial setup by WPS

Get Panasonic KX-HN1003 PDF manuals and user guides View all Panasonic KX-HN1003 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 190 highlights

Troubleshooting Initial setup by WPS WPS WPS is a function of wireless routers that is used to easily connect wireless devices to wireless routers. A WPS button on a wireless router indicates that it has the WPS function. (Depending on the type of wireless router, the WPS function may be disabled on the wireless router even if there is a WPS button.) Initial setup can't be completed The camera's LED indicator is blinking in red. If you have trouble during the initial setup check the following causes/solutions first and then turn off the camera and restart it. R The WPS function on your wireless router may be disabled. Some Internet Service Provider wireless routers may have WPS disabled. →Try initial setup using Bluetooth ( "Initial setup by Bluetooth", Page 191). R The camera and wireless router are too far away. →Move the camera and wireless router closer together. R The wireless router is not in WPS mode. →Press the WPS button on the wireless router for long enough until the LED indicator on the router starts blinking. R Several cameras are in WPS mode. Only 1 camera can be operated in WPS mode at a time. →Turn off all other cameras and only operate 1 camera at a time. R The DHCP function of your wireless router may be disabled. →Enable the wireless router's DHCP settings. For details, refer to your wireless router's manual. R The address filter function of your wireless router may be enabled. →Register the MAC address of the camera to the address filter setting of the wireless router. Refer to your wireless router's manual. The camera's LED indicator is lit in blue. R The WPS button was pressed on another router which is different from the router your mobile device is connected with. →Perform one of the following. - If you want to connect your mobile device to the wireless router which the camera is connected with: Reconnect your mobile device to the router whose WPS button was pressed, restart the [HomeHawk] app, and then follow the on-screen instructions. - If you want to connect your camera to the wireless router which the mobile device is connected with: Press and hold the RESET button for about 10 seconds using an object with a thin tip ( "Resetting camera settings", Page 114) and restart the [HomeHawk] app. Then press the WPS button on the router which your mobile device is connected with. R A network clash has occurred because you have 2 wireless routers at home that are using the same channel or channels of a close frequency. →Unplug all the wireless routers and plug them in again. If the situation still does not improve, refer to your wireless router's manual for information on how to change the router channel of your wireless network. R The "Isolation" function on the wireless router is enabled. Sometimes when the "Isolation" function is enabled, the camera will not be able to communicate with your mobile device via your wireless router. →Disable the "Isolation" function on your wireless router. For details, refer to your wireless router's manual. 190

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
Initial setup by WPS
WPS
WPS is a function of wireless routers that is used to easily connect wireless devices to wireless routers. A
WPS button on a wireless router indicates that it has the WPS function. (Depending on the type of
wireless router, the WPS function may be disabled on the wireless router even if there is a WPS button.)
Initial setup can't be completed
The camera’s LED indicator is blinking in red.
If you have trouble during the initial setup check the following causes/solutions first and then turn off the
camera and restart it.
R
The WPS function on your wireless router may be disabled.
Some Internet Service Provider wireless routers may have WPS disabled.
→Try initial setup using Bluetooth ( “Initial setup by Bluetooth”, Page 191).
R
The camera and wireless router are too far away.
→Move the camera and wireless router closer together.
R
The wireless router is not in WPS mode.
→Press the WPS button on the wireless router for long enough until the LED indicator on the router
starts blinking.
R
Several cameras are in WPS mode.
Only 1 camera can be operated in WPS mode at a time.
→Turn off all other cameras and only operate 1 camera at a time.
R
The DHCP function of your wireless router may be disabled.
→Enable the wireless router’s DHCP settings. For details, refer to your wireless router’s manual.
R
The address filter function of your wireless router may be enabled.
→Register the MAC address of the camera to the address filter setting of the wireless router. Refer to
your wireless router’s manual.
The camera’s LED indicator is lit in blue.
R
The WPS button was pressed on another router which is different from the router your mobile device is
connected with.
→Perform one of the following.
–
If you want to connect your mobile device to the wireless router which the camera is
connected with:
Reconnect your mobile device to the router whose WPS button was pressed, restart the
[HomeHawk]
app, and then follow the on-screen instructions.
–
If you want to connect your camera to the wireless router which the mobile device is
connected with:
Press and hold the
RESET
button for about 10 seconds using an object with a thin tip ( “Resetting
camera settings”, Page 114) and restart the
[HomeHawk]
app. Then press the WPS button on
the router which your mobile device is connected with.
R
A network clash has occurred because you have 2 wireless routers at home that are using the same
channel or channels of a close frequency.
→Unplug all the wireless routers and plug them in again.
If the situation still does not improve, refer to your wireless router’s manual for information on how to
change the router channel of your wireless network.
R
The "Isolation" function on the wireless router is enabled.
Sometimes when the "Isolation" function is enabled, the camera will not be able to communicate with
your mobile device via your wireless router.
→Disable the "Isolation" function on your wireless router. For details, refer to your wireless router’s
manual.
190
Troubleshooting