Panasonic WJHD316 WJHD309 User Guide - Page 102

Set the sensitivity, Set the detection mode, Screenshot 1], <ANY AREA&gt, <VECTOR&gt

Page 102 highlights

x Move the cross cursor onto an area to be deleted using the arrows button and press the SET button. c To complete the settings, rotate the jog dial to select "EXIT" on the status bar. → The "VMD Setup" window will be closed. 8 Set the sensitivity Set the sensitivity for the created motion detection area. Sensitivity can be set for each area. [Screenshot 1] Start operation from the "VMD Setup" window. 8 Set the detection mode Perform the settings of the detection mode (method of detection) in the set detection area. Specifying a method of detection in a detection area is available by setting the detection mode. [Screenshot 1] Start operation from the "VMD Setup" window. z Rotate the jog dial to select "SENSITIVITY" on the status bar. [Screenshot 2] The sensitivity of the selected detection area will be displayed. z Rotate the jog dial to select "VMD MODE" on the status bar. [Screenshot 2] The detection mode menu will be displayed. x Move the cross cursor to select an area using the arrows button (A B). c Select the sensitivity for the selected area from the following. OFF: No motion will be detected in this area. LOW: Low sensitivity MID: Standard sensitivity HIGH: High sensitivity v To complete the settings, rotate the jog dial to select "EXIT" on the status bar, and press the SET button. → The "VMD Setup" window will be closed. x Set the detection mode. Move the cursor to the desired detection mode using the arrows button (A B). Move the cursor on the desired detection mode using the arrows button (A B) and check the radio button next to the selected mode using the arrows button (C D). Refer to the following for further information about each of the detection modes. An event action will be performed according to the settings when "motion" is detected in any of the set motion detection areas. Move the cursor to an area for the settings of VECTOR using the arrows button (B) and select an area using the arrows button (C D). Move the cursor to the parameter box of the selected area using the arrows button (B), and then press the arrows button (C D) to select an interval time for an object moving between each area from the following. --/5 s/10 s/20 s/30 s/40 s/50 s/1 m(min) 102

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164

102
x
Move the cross cursor onto an area to be deleted using
the arrows button and press the SET button.
c
To complete the settings, rotate the jog dial to select
"EXIT" on the status bar.
The "VMD Setup" window will be closed.
8
Set the sensitivity
Set the sensitivity for the created motion detection area.
Sensitivity can be set for each area.
[Screenshot 1]
Start operation from the "VMD Setup" window.
z
Rotate the jog dial to select "SENSITIVITY" on the status
bar.
[Screenshot 2]
The sensitivity of the selected detection area will be dis-
played.
x
Move the cross cursor to select an area using the
arrows button (
A B
).
c
Select the sensitivity for the selected area from the fol-
lowing.
OFF:
No motion will be detected in this area.
LOW:
Low sensitivity
MID:
Standard sensitivity
HIGH:
High sensitivity
v
To complete the settings, rotate the jog dial to select
"EXIT" on the status bar, and press the SET button.
The "VMD Setup" window will be closed.
8
Set the detection mode
Perform the settings of the detection mode (method of
detection) in the set detection area. Specifying a method of
detection in a detection area is available by setting the
detection mode.
[Screenshot 1]
Start operation from the "VMD Setup" window.
z
Rotate the jog dial to select "VMD MODE" on the status
bar.
[Screenshot 2]
The detection mode menu will be displayed.
x
Set the detection mode.
Move the cursor to the desired detection mode using
the arrows button (
AB
).
Move the cursor on the desired detection mode using
the arrows button (
AB
) and check the radio button
next to the selected mode using the arrows button (
C
D
).
Refer to the following for further information about each
of the detection modes.
<ANY AREA>
An event action will be performed according to the set-
tings when "motion" is detected in any of the set motion
detection areas.
<VECTOR>
Move the cursor to an area for the settings of VECTOR
using the arrows button (
B
) and select an area using
the arrows button (
CD
). Move the cursor to the para-
meter box of the selected area using the arrows button
(
B
), and then press the arrows button (
CD
) to select
an interval time for an object moving between each
area from the following.
--/5 s/10 s/20 s/30 s/40 s/50 s/1 m(min)