Panasonic WJHD316 WJHD309 User Guide - Page 162
Specification
View all Panasonic WJHD316 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 162 highlights
SPECIFICATION General Power source: Power consumption Ambient operating temperature Ambient operating humidity Dimensions Weight 220 V - 240 V AC, 50 Hz 85 W +5 °C to +45 °C (41 °F - 113 °F) Less than 85 % 420 mm (W) X 88 mm (H) X 350 mm (D) [16-9/16" (W) X 3-7/16" (H) X 13-3/4" (D)] (excluding rubber feet and projections) 9.5 kg (21 lbs.) Input/Output Video Audio Others Video input connectors 1 V [P-P] / 75 Ω, with auto termination loop-thru, vertical timing pulse multiplexed, x8 (1 to 8 CH) (BNC) 1 V [P-P] / 75 Ω, with auto-termination loop-thru, x8 (9 to 16 CH) (BNC) Cascade input connector Video output connectors 1 V [P-P] / 75 Ω (BNC) 1 V [P-P] / 75 Ω, active loop-thru output, x8 (1 to 8 CH) (BNC)*1 1 V [P-P] / 75 Ω, active loop-thru output, x8 (9 to 16 CH) (BNC) Monitor output connectors 1 V [P-P] / 75 Ω, x2 (BNC) Monitor output connector RGB output, x1 (15-pin D-sub) (VGA) S-video output connector Y = 1 V [P-P] / 75 Ω, C=0.286 V [P-P] / 75 Ω, x1 (S-video output connector) Video output connector (front panel) 1 V [P-P] / 75 Ω, x1 (RCA pin) Audio input connectors Audio output connectors Expansion connector Copy connectors Control connectors -10 dB, 10 KΩ, x4 (RCA pin) -10 dB, 600 Ω, unbalanced, x2 (RCA pin) High-speed serial interface, 480 Mbps (theoretical value), x1 High-speed serial interface, 480 Mbps (theoretical value), x2 Emergency recording input*2, additional space warning output*3 (for devices connected to copy connectors), HDD trouble output*3, camera trouble output*3, trouble output*3, electricity failure recovery completion output*4, time adjust input/output*5, sequence switching input/output*5, electricity failure detection input*2, external recording mode switching*2 (25-pin D-sub) , +5 V output *7 Alarm port RS-485 ports DATA ports SERIAL connector Ethernet port 1 to 8 CH alarm input*6, 1 to 16 CH alarm input*2, 1 to 16 alarm output*3, alarm recovery input*2, alarm suspension input*5 (25-pin D-sub) RS-485 (full duplex/half duplex*8), x2 (RJ-11) RS-485, x2 (RJ-11) RS-232C, x1 (9-pin D-sub) 10 Base-T/100 Base-Tx (RJ-45) *1 When power is not supplied, the video output signal was not sent from the unit even if a video input signal is supplied. *2 Non-voltage N.O. Contact, 100 mA, +5 V pull-up *3 Open collector output, maximum under conditions of 24 V DC and 100 mA or less *4 High (+12 V, 6.3 mA) *5 30 KΩ, 5 V pull-up, -100 mA, N.O. Contact *6 5 V pull-up, -100 mA, Non-voltage N.O. Contact input *7 200 mA at maximum *8 Changeable with the mode switch 162