Pioneer DEH-80PRS Owner's Manual - Page 6

Switching between RCA, input modes, Demo mode, About this manual, Before you start - install

Get Pioneer DEH-80PRS PDF manuals and user guides View all Pioneer DEH-80PRS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Section 01 Before you start 1 Use a thin, flathead screwdriver to change the DSP switch on the bottom of this unit. ! L (Low) - If inputting from the RCA output of a connected device ! H (High) - If inputting from the speaker output of a connected device 2 Press RESET with a pen tip or other pointed instrument. Note This unit's audio settings will continue to remain in the memory even if the battery is disconnected or the microprocessor reset. If you want to reset the audio settings, refer to AUDIO reset (audio reset) on page 36. Switching between RCA input modes If you connect the unit to an audio device with RCA output, or to one with no RCA output, you can set it up so that the audio from the audio device is output through speakers connected to the unit. Change settings as necessary based on whether the connected device has RCA output or not. ! For more details on how to connect the unit, refer to the installation manual. % Use a thin, flathead screwdriver to change the RCA input mode switch on the bottom of this unit. Demo mode Important ! Failure to connect the red lead (ACC) of this unit to a terminal coupled with ignition switch on/off operations may lead to battery drain. ! Remember that if the feature demo continues operating when the car engine is turned off, it may drain battery power. The demo starts automatically if you do not operate this unit within about 30 seconds since it was last operated or if the ignition switch is set to ACC or ON while it is turned off. To cancel the demo mode, press and hold ( /DISP). Press and hold ( /DISP) again to start. You can also deactivate demo mode in the initial settings. Select Demonstration (demo display setting) and turn off the demo display. For details, refer to Initial settings on page 35. About this manual ! In the following instructions, USB memories, USB portable audio players, and SD memory cards are collectively referred to as "external storage devices (USB, SD)". If only USB memories and USB portable audio players are indicated, they are collectively referred to as "USB storage devices". ! In this manual, iPod and iPhone will be referred to as "iPod". 6 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
1
Use a thin, flathead screwdriver to
change the DSP switch on the bottom of
this unit.
2
Press RESET with a pen tip or other
pointed instrument.
Note
This unit's audio settings will continue to remain
in the memory even if the battery is disconnected
or the microprocessor reset. If you want to reset
the audio settings, refer to
AUDIO reset
(audio
reset)
on page 36.
Switching between RCA
input modes
If you connect the unit to an audio device with
RCA output, or to one with no RCA output,
you can set it up so that the audio from the
audio device is output through speakers con-
nected to the unit. Change settings as neces-
sary based on whether the connected device
has RCA output or not.
!
For more details on how to connect the
unit, refer to the installation manual.
%
Use a thin, flathead screwdriver to
change the RCA input mode switch on the
bottom of this unit.
!
L
(Low) - If inputting from the RCA output of
a connected device
!
H
(High) - If inputting from the speaker out-
put of a connected device
Demo mode
Important
!
Failure to connect the red lead (ACC) of this
unit to a terminal coupled with ignition switch
on/off operations may lead to battery drain.
!
Remember that if the feature demo continues
operating when the car engine is turned off, it
may drain battery power.
The demo starts automatically if you do not op-
erate this unit within about 30 seconds since it
was last operated or if the ignition switch is
set to ACC or ON while it is turned off. To can-
cel the demo mode, press and hold (
/
DISP
).
Press and hold (
/
DISP
) again to start. You
can also deactivate demo mode in the initial
settings. Select
Demonstration
(demo display
setting)
and turn off the demo display. For de-
tails, refer to
Initial settings
on page 35.
About this manual
!
In the following instructions, USB mem-
ories, USB portable audio players, and SD
memory cards are collectively referred to as
“
external storage devices (USB, SD)
”
. If
only USB memories and USB portable
audio players are indicated, they are collec-
tively referred to as
“
USB storage devices
”
.
!
In this manual, iPod and iPhone will be re-
ferred to as
“
iPod
”
.
En
6
Section
01
Before you start