Pioneer VSX 818V Owner's Manual - Page 72

Additional information, Resetting the main unit, Switching the speaker, impedance, Specifications

Get Pioneer VSX 818V - AV Receiver PDF manuals and user guides
UPC - 012562884769
View all Pioneer VSX 818V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

12 Additional information Resetting the main unit Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. 1 Switch the receiver into standby. 2 While holding down the ADVANCED SURROUND button, press and hold the STANDBY/ON button for about three seconds. 3 When you see RESET? appear in the display, press 'ST -'. OK? shows in the display. 4 Press SOUND RETRIEVER to confirm. OK appears in the display to indicate that the receiver has been reset to the factory settings. Switching the speaker impedance We recommend using speakers of 8 Ω with this system, but it is possible to switch the impedance setting if you plan to use speakers with a 6 Ω impedance rating. • With the receiver in standby, press STANDBY/ON while holding down the SPEAKERS button. Each time you do this, you switch between the impedance settings: • SP 6 OHM - Use this setting if your speakers are rated at 6 Ω. • SP 8 OHM - Use this setting if your speakers are rated at 8 Ω or more. Specifications Amplifier section • Continuous power output (stereo) Front . . .95 W (20 Hz to 20 kHz, THD 0.2 %, 8 Ω)1 • Rated power output (surround / 20 Hz to 20 kHz, THD 0.06 %, 8 Ω) Front 95 W per channel Center 95 W Surround 95 W per channel • Rated power output (surround / 1 kHz, THD 0.05 %, 8 Ω) Front 120 W per channel Center 120 W Surround 120 W per channel Audio section • Input (Sensitivity/Impedance) AUX, CD, CD-R/TAPE/MD, DVD/BD, TV/SAT, DVR/VCR 335 mV/47 kΩ • Frequency response AUX, CD, CD-R/TAPE/MD, DVD/BD, TV/SAT, DVR/VCR . . . . . 5 Hz to 100 000 Hz dB • Output (Level/Impedance) CD-R/TAPE/MD, DVR/VCR 335 mV/2.2 kΩ • Tone control Bass 6 dB (100 Hz) Treble 6 dB (10 kHz) Loudness 10 dB/+5 dB (100 Hz/10 kHz) (at volume level -50 dB) • Signal-to-Noise Ratio (IHF, short circuited, A network) AUX, CD, CD-R/TAPE/MD, DVD/BD, TV/SAT, DVR/VCR 96 dB • Signal-to Noise Ratio [EIA, at 1 W (1 kHz)] AUX, CD, CD-R/TAPE/MD, DVD/BD, TV/SAT, DVR/VCR 79 dB Note 1 Continuous average power output of 95 watts* per channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no more than 0.2 %** total harmonic distortion (front). * Measured pursuant to the Federal Trade Commission's Trade Regulation rule on Power Output Claims for Amplifiers. ** Measured by Audio Spectrum Analyzer. 72 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Additional information
12
72
En
Resetting the main unit
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front
panel controls to do this.
1
Switch the receiver into standby.
2
While holding down the ADVANCED
SURROUND button, press and hold the
²
STANDBY/ON button for about three
seconds.
3
When you see RESET? appear in the
display, press ‘
ST –
’.
OK?
shows in the display.
4
Press
SOUND RETRIEVER
to confirm.
OK
appears in the display to indicate that the
receiver has been reset to the factory settings.
Switching the speaker
impedance
We recommend using speakers of 8
Ω
with
this system, but it is possible to switch the
impedance setting if you plan to use speakers
with a 6
Ω
impedance rating.
•
With the receiver in standby, press
²
STANDBY/ON
while holding down the
SPEAKERS
button.
Each time you do this, you switch between the
impedance settings:
•
SP 6 OHM
– Use this setting if your
speakers are rated at 6
Ω
.
•
SP 8 OHM
– Use this setting if your
speakers are rated at 8
Ω
or more.
Specifications
Amplifier section
•
Continuous power output
(stereo)
Front . . .95 W (20 Hz to 20 kHz, THD 0.2 %, 8
Ω
)
1
•
Rated power output
(surround / 20 Hz to 20 kHz, THD 0.06 %, 8
Ω
)
Front . . . . . . . . . . . . . . . . . . . . . .95 W per channel
Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 W
Surround. . . . . . . . . . . . . . . . . . .95 W per channel
•
Rated power output
(surround / 1 kHz, THD 0.05 %, 8
Ω
)
Front . . . . . . . . . . . . . . . . . . . . .120 W per channel
Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 W
Surround. . . . . . . . . . . . . . . . . .120 W per channel
Audio section
•
Input (Sensitivity/Impedance)
AUX, CD, CD-R/TAPE/MD, DVD/BD,
TV/SAT, DVR/VCR . . . . . . . . . . . . . .335 mV/47 k
Ω
•
Frequency response
AUX, CD, CD-R/TAPE/MD, DVD/BD,
TV/SAT, DVR/VCR . . . . .5 Hz to 100 000 Hz
dB
•
Output (Level/Impedance)
CD-R/TAPE/MD, DVR/VCR . . . . . . 335 mV/2.2 k
Ω
•
Tone control
Bass . . . . . . . . . . . . . . . . . . . . . . . ± 6 dB (100 Hz)
Treble . . . . . . . . . . . . . . . . . . . . . . ± 6 dB (10 kHz)
Loudness . . . . . . +10 dB/+5 dB (100 Hz/10 kHz)
(at volume level –50 dB)
•
Signal-to-Noise Ratio (IHF, short circuited,
A network)
AUX, CD, CD-R/TAPE/MD, DVD/BD,
TV/SAT, DVR/VCR . . . . . . . . . . . . . . . . . . . . .96 dB
•
Signal-to Noise Ratio [EIA, at 1 W (1 kHz)]
AUX, CD, CD-R/TAPE/MD, DVD/BD,
TV/SAT, DVR/VCR . . . . . . . . . . . . . . . . . . . . 79 dB
Note
1
Continuous average power output of 95 watts* per channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no more than
0.2 %** total harmonic distortion (front).
* Measured pursuant to the Federal Trade Commission’s Trade Regulation rule on Power Output Claims for Amplifiers.
** Measured by Audio Spectrum Analyzer.