Ridgid R4030 Operation Manual - Page 16

Filling/changing The Water Reservoir, To Control The Flow Of Water - wet saw

Get Ridgid R4030 PDF manuals and user guides View all Ridgid R4030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

ASSEMBLY FILLING/CHANGING THE WATER RESERVOIR See Figures 15-16.  Fill the water reservoir with clean tap water to the fill line. Do not fill past the Max Fill line on the tray. To change reservoir water:  Unplug the saw.  Remove the drain plug and empty waste water into a bucket. Do not allow the water to splash onto the ground or around the machine.  Rinse the machine thoroughly.  Discard the waste water in accordance with local regulations.  Replace the drain plug and refill tray with clean water. TO CONTROL THE FLOW OF WATER See Figure 17.  Fill the water tray with clean water as described below.  Locate the "Max/Min" water flow selector on the pump. For best performance, set the flow to "Max" to control the flow of water over the wheel.  The pump turns on when the motor is turned on. Let the cutting wheel build up to full speed and wait for the wheel to get wet before moving the material into the wheel. FILL LINE WATER RESERVOIR Fig. 15 DRAIN PLUG Fig. 16 16 - English WATER FLOW SELECTOR MIN MAX MAX MIN Fig. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
16 — English
Fig. 17
DRAIN
PLUG
MAX
MIN
ASSEMBLY
FILLING/CHANGING THE WATER RESERVOIR
See Figures 15-16.
Fill the water reservoir with clean tap water to the fill line.
Do not fill past the Max Fill line on the tray.
To change reservoir water:
Unplug the saw.
Remove the drain plug and empty waste water into a
bucket. Do not allow the water to splash onto the ground
or around the machine.
Rinse the machine thoroughly.
Discard the waste water in accordance with local regula-
tions.
Replace the drain plug and refill tray with clean water.
TO CONTROL THE FLOW OF WATER
See Figure 17.
Fill the water tray with clean water as described below.
Locate the “Max/Min” water flow selector on the pump.
For best performance, set the flow to “Max” to control
the flow of water over the wheel.
The pump turns on when the motor is turned on. Let the
cutting wheel build up to full speed and wait for the wheel
to get wet before moving the material into the wheel.
Fig. 15
FILL LINE
WATER
RESERVOIR
Fig. 16
WATER
FLOW
SELECTOR
MAX
MIN