Ridgid R4030 Operation Manual - Page 17

Danger, Warning, Installing Laser Batteries, Using The Laser Guide - user manual

Get Ridgid R4030 PDF manuals and user guides View all Ridgid R4030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

ASSEMBLY DANGER: Laser radiation. Avoid direct eye contact with light source. WARNING: Use of controls or adjustments or performance of procedures other than those specified herein could result in hazardous radiation exposure. INSTALLING LASER BATTERIES See Figure 18.  Remove screw from battery compartment cover using the Phillips end of the supplied arbor wrench. Remove cover and set aside.  Install two AAA batteries according to polarity indicators inside the battery compartment.  Replace the battery compartment cover. Reinstall screw and tighten securely. USING THE LASER GUIDE See Figure 19. Draw a line on the tile. When the laser guide switch is turned on it will generate a red line on the work surface. This line will assist you in lining up the mark for more accurate cutting of the tile. Align the laser line and the mark with the wheel in the cutting position using the laser adjustment screw. Make several practice cuts on different styles and thickness of material. Repeat the steps as necessary. BATTERY COVER AAA AAA SCREW • To reduce the risk of injury, the user must read and understand operator's manual. • Wear eye, hearing, and respiratory protection when operatingthe tool. • Do not remove the wheel guard. • Never operate the tool without the wheel guard securely closed. • Turn off tool, wait for the wheel to stop moving and disconnect the power to the tool before servicing, when changing cutting wheels, or cleaning. • Never use wheels that have openings, grooves, or teeth on this tool. • Always inspect and replace damaged cutting wheels before operating the tool. • Do not expose to rain or other damp locations. • Do not fill water bath above maximum water fill line. • Do not stack or store tiles on water trays. • Use splash hood for every operation for which it can be used. COMPLIES WITH 21 CFR PARTS 1040.10 AND 1040.11 RYLD 640-670 LASER GUIDE SWITCH Fig. 18 AVOID EXPOSURE: Laser radiation is emitted from this aperture. ÉVITER L'EXPOSITION : Radiation laser émise de cet orifice. EVITE LA EXPOSICIÓN: La radiación láser se emite por esta abertura. 17 - English Fig. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
17 — English
DANGER:
Laser radiation. Avoid direct eye contact with light
source.
WARNING:
Use of controls or adjustments or performance of
procedures other than those specified herein could
result in hazardous radiation exposure.
INSTALLING LASER BATTERIES
See Figure 18.
Remove screw from battery compartment cover using
the Phillips end of the supplied arbor wrench. Remove
cover and set aside.
Install two AAA batteries according to polarity indicators
inside the battery compartment.
Replace the battery compartment cover. Reinstall screw
and tighten securely.
USING THE LASER GUIDE
See Figure 19.
Draw a line on the tile. When the laser guide switch is turned
on it will generate a red line on the work surface. This line
will assist you in lining up the mark for more accurate cut-
ting of the tile.
Align the laser line and the mark with the wheel in the
cutting position using the laser adjustment screw.
Make several practice cuts on different styles and thickness
of material. Repeat the steps as necessary.
ASSEMBLY
Fig. 18
LASER GUIDE
SWITCH
Fig. 19
AAA
AAA
SCREW
BATTERY
COVER
AVOID EXPOSURE:
Laser radiation is emitted from this
aperture.
ÉVITER L'EXPOSITION :
Radiation laser émise de cet orifice.
EVITE LA EXPOSICIÓN:
La radiación láser se emite por
esta abertura.
640-670
•
To reduce the risk of injury, the user must read and understand
operator’s manual.
•
Do not fill water bath above maximum water fill line.
•
Do not stack or store tiles on water trays.
•
Do not expose to rain or other damp locations.
•
Always inspect and replace damaged cutting wheels before operating
the tool.
•
Never use wheels that have openings, grooves, or teeth on this tool.
•
Turn off tool, wait for the wheel to stop moving and disconnect
the power to the tool before servicing, when changing cutting
wheels, or cleaning.
•
Never operate the tool without the wheel guard securely closed.
•
Do not remove the wheel guard.
•
Wear eye, hearing, and respiratory protection when operating the tool.
•
Use splash hood for every operation for which it can be used.
COMPLIES WITH 21 CFR PARTS 1040.10 AND 1040.11
RYLD