Sharp AR-P450 AR-P350 AR-P450 Operation Manual - Page 79

Loading paper in the bypass tray, DUPLEX MODULE

Get Sharp AR-P450 PDF manuals and user guides View all Sharp AR-P450 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

DUPLEX MODULE Loading paper in the bypass tray The bypass tray can be used for plain paper and special papers including labels. Up to 100 sheets of standard paper can be set. For paper types that can be used in the bypass tray, refer to page 1-17. NOTE If the paper type or size is changed, be sure to enter the paper type and size as in step 4. 1 Open the bypass tray. NOTES q When using 5-1/2" x 8-1/2" paper, A5 paper or postcards, be sure to load them with their shorter edge into the feed slot as shown in the illustration. Bypass tray extension When setting 11"x 17", 8-1/2" x 14", 8-1/2" x 13, A3 or B4 paper, be sure to extend the bypass tray extension. 2 Set the bypass tray paper guides to the width of the paper to be used. 3 Insert the paper all the way into the bypass tray. Set the paper face down. If there is a clearance between the paper and the paper guides, the paper may not be fed correctly. Adjust the guides so that they contact the edges of the paper. q When using special paper, postcards or transparency film, be sure to feed them one 5 sheet at a time. If you set more than one sheet, a paper misfeed may occur. q When adding paper, first remove remaining paper, combine it with the paper to be added, and then reload as a single stack. Adding paper without stacking it correctly may cause a paper misfeed. q When printing onto transparency film, remove the output sheets as soon as possible. q For transparency film, use SHARP recommended film. 4 Set the type and size of the loaded paper. When the paper system is changed from the inch system to the AB system or vise versa or when the paper type is changed, the paper type must be designated. For setting the paper size and type, see page 1-19. 5 Loading paper in the bypass tray is now complete. 5-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
5-3
5
Loading paper in the bypass tray
The bypass tray can be used for plain paper and special papers including labels. Up to 100 sheets of standard paper
can be set. For paper types that can be used in the bypass tray, refer to page 1-17.
NOTE
If the paper type or size is changed, be sure to enter the paper type and size as in step 4.
1
Open the bypass tray.
When setting 11"x 17",
8-1/2" x 14", 8-1/2" x 13,
A3 or B4 paper, be sure
to extend the bypass tray
extension.
2
Set the bypass tray paper guides to the
width of the paper to be used.
3
Insert the paper all the way into the bypass
tray.
Set the paper face down.
If there is a clearance
between the paper and
the paper guides, the
paper may not be fed
correctly. Adjust the
guides so that they
contact the edges of the
paper.
NOTES
●
When using 5-1/2" x 8-1/2" paper, A5 paper or
postcards, be sure to load them with their shorter
edge into the feed slot as shown in the illustration.
●
When using special paper, postcards or
transparency film, be sure to feed them one
sheet at a time. If you set more than one sheet,
a paper misfeed may occur.
●
When adding paper, first remove remaining
paper, combine it with the paper to be added,
and then reload as a single stack. Adding paper
without stacking it correctly may cause a paper
misfeed.
●
When printing onto transparency film, remove
the output sheets as soon as possible.
●
For transparency film, use SHARP recom-
mended film.
4
Set the type and size of the loaded paper.
When the paper system is changed from the inch
system to the AB system or vise versa or when the
paper type is changed, the paper type must be
designated. For setting the paper size and type, see
page 1-19.
5
Loading paper in the bypass tray is now
complete.
DUPLEX MODULE
Bypass tray extension