Sharp PN-V701 PN-V701 Operation Manual - Page 37
Initialization (Reset)/Functional Restriction Setting (FUNCTION
View all Sharp PN-V701 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 37 highlights
Initialization (Reset)/Functional Restriction Setting (FUNCTION) You can return the settings to their factory-preset values and restrict operations. 1. If using the remote control unit: Press the FUNCTION button, and then press the MENU button within 10 seconds. If using the monitor buttons: Press the MENU button and INPUT button at the same time until "F" is displayed in the upper left area of the screen, then while "F" is being displayed, press the MENU button. FUNCTION ALL RESET ADJUSTMENT LOCK ADJUSTMENT LOCK TARGET RS-232C/LAN OSD DISPLAY OFF UNLOCKED ON 1 LED ON TEMPERATURE ALERT LED STATUS ALERT LED POWER BUTTON MONITOR EXTERNAL CONTROLLER INPUT SIGNAL RESPONSE LEVEL 1 OK:[ENTER] END:[RETURN] 2. Select and set the items. ALL RESET Resets the settings to the factory default settings. Press the ENTER button, select the resetting method, and then press the ENTER button. After initialization, turn the main power switch off and then back on. ALL RESET1 Resets all the settings to the factory default settings. ALL RESET2 Returns all settings to the factory default settings except for the following items: LAN SETUP, RS-232C/LAN SELECT, ID No. SET, REMOTE No., BAUD RATE, NETWORK, MAIL, SERVICE & SUPPORT, and SNMP (See page 29, and pages 55 to 58.) ADJUSTMENT LOCK You can disable operations on the monitor and the remote control unit that use buttons. OFF ���Enables operation. ON 1 ��Disables all operations other than turning power on/off and FUNCTION. ON 2 ��Only the FUNCTION operation is enabled. Disables all operations other than FUNCTION (not even power on/off). ADJUSTMENT LOCK TARGET Sets the target to prohibit operation of with ADJUSTMENT LOCK. REMOTE CONTROL Prohibits remote control operation MONITOR BUTTONS ��� Prohibits monitor button operation BOTH Prohibits remote control and monitor button operation RS-232C/LAN Specifies whether to allow control via RS-232C or LAN (see pages 38 and 51). OSD DISPLAY Shows/hides the menu, modes and messages. The FUNCTION and REMOTE CONTROL MODE screens cannot be hidden. ON 1 Shows all menus, modes and messages. ON 2 Hides messages automatically displayed by the display. Shows messages during operation. OFF Hides all menus, modes and messages. LED Specifies whether to light the power LED. TEMPERATURE ALERT Selects the notification method for an abnormal temperature. OFF Do not notify about an abnormal temperature. OSD & LED �� When an abnormal temperature is detected, the power LED flashes in red and green alternately and the screen displays a message: TEMPERATURE. LED When an abnormal temperature is detected, the power LED flashes in red and green alternately. STATUS ALERT Selects the notification method for a hardware error. OFF Do not notify about the error. OSD & LED �� When a hardware error is detected, the power LED flashes in red and the screen displays a message: STATUS [xxxx]. LED When a hardware error is detected, the power LED flashes in red. POWER BUTTON Normally, leave this setting as MONITOR. When using an optional part, if instruction appears, change the setting accordingly. EXTERNAL CONTROLLER INPUT Normally, you do not need to change this setting. When using an optional part, if instruction appears, change the setting accordingly. SIGNAL RESPONSE LEVEL Normally, you do not need to change this setting. Use this option to set the level of response to signal changes. 3. Press the RETURN button to return to the normal screen. TIPS • When both abnormal temperature and hardware error are detected, the hardware error notification overrides. • If TEMPERATURE ALERT or STATUS ALERT is set to OSD&LED, alert messages will appear even if the OSD DISPLAY is set to ON 2 or OFF. • If TEMPERATURE ALERT or STATUS ALERT is set to LED or OSD & LED, the LED lights even if the LED function is set to OFF. 37 E