Sharp XG-C435X XG-C435X XG-C465X Operation Manual - Page 63

Removing and Installing the Lamp Unit, tor into standby mode.

Get Sharp XG-C435X - XGA LCD Projector PDF manuals and user guides View all Sharp XG-C435X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Removing and Installing the Lamp Unit Warning! • Do not remove the lamp unit from the pro- jector right after use. The lamp and parts around the lamp will be very hot and may cause burn or injury. Info • Do not touch the glass surface of the lamp unit or the inside of the projector. • To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below. • Do not loosen other screws except for the lamp unit cover and lamp unit. 1 Press STANDBY/ON on the projector or STANDBY on the remote control to put the projector into standby mode. • Wait until the cooling fan stops. 2 Disconnect the power cord. • Unplug the power cord from the AC socket. • Leave the lamp until it has fully cooled down (about 1 hour). 3 Remove the lamp unit cover. • Loosen the user service screw (1) that secures the lamp unit cover. Slide down (2) and remove the lamp unit cover (3). 4 Remove the lamp unit. • Loosen the securing screws from the lamp unit. Hold the lamp unit and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it. Optional accessory Lamp unit AN-C430LP STANDBY/ON button AC socket 2 3 1 User service screw (for lamp unit cover) Securing screws Appendix -61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
-61
Appendix
Securing screws
Optional
accessory
Lamp unit
AN-C430LP
Removing and Installing
the Lamp Unit
Warning!
•
Do not remove the lamp unit from the pro-
jector right after use. The lamp and parts
around the lamp will be very hot and may
cause burn or injury.
Info
•
Do not touch the glass surface of the lamp
unit or the inside of the projector.
•
To avoid injury to yourself and damage to
the lamp, make sure you carefully follow
the steps below.
•
Do not loosen other screws except for the
lamp unit cover and lamp unit.
1
Press
STANDBY/ON on the
projector or
STANDBY on the
remote control to put the projec-
tor into standby mode.
•
Wait until the cooling fan stops.
2
Disconnect the power cord.
•
Unplug the power cord from the AC
socket.
•
Leave the lamp until it has fully cooled
down (about 1 hour).
3
Remove the lamp unit cover.
•
Loosen the user service screw (
1
) that
secures the lamp unit cover. Slide down
(
2
) and remove the lamp unit cover
(
3
).
4
Remove the lamp unit.
•
Loosen the securing screws from the
lamp unit. Hold the lamp unit and pull it
in the direction of the arrow. At this time,
keep the lamp unit horizontal and do not
tilt it.
AC socket
1
3
2
User service screw
(for lamp unit cover)
STANDBY/ON
button