Sony BRC-X400 Operating Instructions - Page 26

Operations Using the Supplied Infrared Remote Commander, Before Starting Operations

Get Sony BRC-X400 PDF manuals and user guides View all Sony BRC-X400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Operations Using the Supplied Infrared Remote Commander Before Starting Operations Before operating, check that the camera and peripheral devices are properly installed and connected. For details, see "Installing the Camera" (page 16) and "Connecting the Camera" (page 19). Turning on the Power Operating Multiple Cameras Using the Infrared Remote Commander 1 Set the IR SELECT switch on the back of the camera you want to operate to 1, 2, or 3. 2 Press the CAMERA SELECT button on the remote commander that corresponds to the number set in step 1. CAMERA SELECT To the AC adapter (supplied) POWER lights 1 Connect the camera to an AC outlet using the supplied AC adapter and power cord. Or, connect the powered PoE+ power supply device and the camera with a LAN cable. The power is turned on and the POWER lamp turns green. The camera will automatically pan and tilt and then stop to the position stored as PRESET 1 (pan/tilt reset). 2 Turn on the peripheral devices. If the POWER button on the remote commander is pressed while the camera is turned on, the camera goes into the standby mode. The POWER lamp turns from green to orange. Note Wait at least 10 seconds if you want to turn on the camera again after putting it in the standby mode. You can then operate the specified camera(s). Every time you operate the camera(s) using the remote commander, the CAMERA SELECT button pressed in step 2 lights up. 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
26
Operations Using the Supplied Infrared
Remote Commander
Before Starting Operations
Before operating, check that the camera and
peripheral devices are properly installed and
connected.
For details, see “Installing the Camera” (page 16)
and “Connecting the Camera” (page 19).
Turning on the Power
1
Connect the camera to an AC outlet using
the supplied AC adapter and power cord.
Or, connect the powered PoE+ power supply
device and the camera with a LAN cable.
The power is turned on and the POWER lamp
turns green.
The camera will automatically pan and tilt
and then stop to the position stored as
PRESET 1 (pan/tilt reset).
2
Turn on the peripheral devices.
If the POWER button on the remote
commander is pressed while the camera is
turned on, the camera goes into the standby
mode. The POWER lamp turns from green to
orange.
Note
Wait at least 10 seconds if you want to turn on the
camera again after putting it in the standby
mode.
Operating Multiple Cameras
Using the Infrared Remote
Commander
1
Set the IR SELECT switch on the back of the
camera you want to operate to 1, 2, or 3.
2
Press the CAMERA SELECT button on the
remote commander that corresponds to the
number set in step 1.
You can then operate the specified camera(s).
Every time you operate the camera(s) using the
remote commander, the CAMERA SELECT button
pressed in step 2 lights up.
POWER lights
To the AC adapter (supplied)
CAMERA SELECT