Sony BRC-X400 Operating Instructions - Page 67

Installation tab, System

Get Sony BRC-X400 PDF manuals and user guides View all Sony BRC-X400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Note If the time zone selected in [Time zone] is different from that set on the computer, the date and time applied the time zone difference to are set on the camera. Installation tab Use this tab to perform settings related to installation. You can configure the settings from the OSD menu. For details, see "SYSTEM Menu" (page 46) or "VIDEO OUT Menu" (page 45). System Image flip (SYSTEM - IMG FLIP) Flip an image vertically. Normally clear the checkbox before use. Select the checkbox when installing the camera on the ceiling. Note When the [Image flip] setting is changed, the coordinates for pan and tilt are flipped and the following are reset. -Pan-Tilt limit (PAN-TILT LIMIT) -Preset IR receive (SYSTEM - IR RECEIVE) If you clear the checkbox, the camera does not receive signals from the supplied remote commander. Be sure to select the checkbox when you use the supplied remote commander. Tally level (SYSTEM - TALLY LEVEL) (BRC-X400/ X401) This is the setting related to the tally lamp. [High]: Brightens the tally lamp. [Low]: Darkens the tally lamp. [Off]: Even when the tally-lamp-ON command is issued, the tally lamp does not light up. Tele convert (SYSTEM - TELE CONVERT MODE) (BRC-X400/X401, SRG-X402) When this is selected, you can shoot using 2× magnification. Notes • This is enabled only when the SYSTEM SELECT switch or format setting of video output is set to 1920×1080. • Selecting the checkbox of [Tele convert] narrows the angle of view. Menu overlay (SDI) Clearing the checkbox does not display the OSD menu or message on the SDI output screen. Menu overlay (HDMI) Clearing the checkbox does not display the OSD menu or message on the HDMI output screen. Standby mode (SYSTEM - STANDBY MODE) This is the function to move the pan position to the end automatically when the camera enters in the standby mode. [Neutral]: The pan position is not moved automatically. [Side]: The pan position is moved to the end automatically. Notes • When the mode is set to [Side], the pan position is moved to the end exceeding the limit even if the Pan-Tilt limit is specified. • After the camera is turned on from the standby mode, the camera position moves to the position recorded on PRESET1. 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
67
Note
If the time zone selected in [Time zone] is different
from that set on the computer, the date and time
applied the time zone difference to are set on the
camera.
Installation tab
Use this tab to perform settings related to
installation.
You can configure the settings from the OSD
menu. For details, see “SYSTEM Menu” (page 46)
or “VIDEO OUT Menu” (page 45).
System
Image flip (SYSTEM - IMG FLIP)
Flip an image vertically. Normally clear the checkbox
before use. Select the checkbox when installing the
camera on the ceiling.
Note
When the [Image flip] setting is changed, the
coordinates for pan and tilt are flipped and the
following are reset.
-Pan-Tilt limit (PAN-TILT LIMIT)
-Preset
IR receive (SYSTEM - IR RECEIVE)
If you clear the checkbox, the camera does not
receive signals from the supplied remote
commander. Be sure to select the checkbox when
you use the supplied remote commander.
Tally level (SYSTEM - TALLY LEVEL) (BRC-X400/
X401)
This is the setting related to the tally lamp.
[High]:
Brightens the tally lamp.
[Low]:
Darkens the tally lamp.
[Off]:
Even when the tally-lamp-ON command is
issued, the tally lamp does not light up.
Tele convert (SYSTEM - TELE CONVERT MODE)
(BRC-X400/X401, SRG-X402)
When this is selected, you can shoot using 2×
magnification.
Notes
• This is enabled only when the SYSTEM
SELECT switch or format setting of video
output is set to 1920×1080.
• Selecting the checkbox of [Tele convert]
narrows the angle of view.
Menu overlay (SDI)
Clearing the checkbox does not display the OSD
menu or message on the SDI output screen.
Menu overlay (HDMI)
Clearing the checkbox does not display the OSD
menu or message on the HDMI output screen.
Standby mode (SYSTEM – STANDBY MODE)
This is the function to move the pan position to the
end automatically when the camera enters in the
standby mode.
[Neutral]:
The pan position is not moved
automatically.
[Side]:
The pan position is moved to the end
automatically.
Notes
• When the mode is set to [Side], the pan
position is moved to the end exceeding the
limit even if the Pan-Tilt limit is specified.
• After the camera is turned on from the
standby mode, the camera position moves
to the position recorded on PRESET1.