Sony BRC-X400 Operating Instructions - Page 46

SYSTEM Menu, TALLY LEVEL System - Tally level BRC

Get Sony BRC-X400 PDF manuals and user guides View all Sony BRC-X400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

SYSTEM Menu You can set the menu from the Administrator menu on a web browser. For details, see "Installation tab" (page 67) or "PTZF control tab" (page 88). IMG FLIP (System - Image flip) When [IMG FLIP] is set to [ON], the picture is flipped vertically and picture shift direction by the pan/tilt operation is also reversed. After the [IMG FLIP] setting is changed, turn off the camera and turn it on again to activate the change. Note When the [IMG FLIP] setting is changed, the coordinates for pan and tilt are flipped and the following are reset. - Pan-Tilt limit (PAN-TILT LIMIT) - Preset IR RECEIVE (System - IR receive) If this is turned [OFF], the camera does not receive signals from the supplied remote commander. Be sure to turn this [ON] when you use the supplied remote commander. Note You cannot set [IR RECEIVE] to [OFF] when using the supplied remote commander. Set [IR RECEIVE] to [OFF] using the remote controller (not supplied) or from the Administrator menu on the web browser. TALLY LEVEL (System - Tally level) (BRCX400/X401) This allows you to configure the settings related to the tally lamp on the front of the camera. Choose from [HIGH], [LOW], and [OFF]. [HIGH]: When the tally lamp is turned on, it comes on bright. [LOW]: When the tally lamp is turned on, it comes on dim. [OFF]: Even when the tally-lamp-ON command is received, the tally lamp does not light up. Note When [TALLY LEVEL] is set to [OFF], the tally lamp does not light up. TELE CONVERT MODE (System - Tele convert) (BRC-X400/X401, SRG-X402) You can shoot using 2× magnification. [OFF]: Does not use the magnification function. [2x]: Uses the magnification function. Notes • This is enabled only when the SYSTEM SELECT switch or the [VIDEO FORMAT] setting is set to 1920×1080. • The angle of view when [TELE CONVERT MODE] is set to [2x] is narrower than when set to [OFF]. • When used with the image stabilizer function, image quality may be degraded. Set [IMAGE STABILIZER] (Image stabilizer) to [OFF] if desired. HTTP/RTSP When the setting of the CAMERA SETUP (camera setup) switch 3 (HTTP/RTSP communication use setting) on the back of the camera is "OFF" (MENU), use this setting to turn ON/OFF the HTTP/RTSP communication. Turn ON the HTTP/ RTSP communication to set the camera with the web browser or acquire streaming. [OFF]:Turn OFF the HTTP/RTSP communication function of the camera. [ON]: Turn ON the HTTP/RTSP communication function of the camera. After the [HTTP/RTSP] setting is changed, turn off the camera and turn it on again to activate the change. Note [HTTP/RTSP] cannot be set on the web browser. PRESET MODE (Preset - Preset mode) (BRC-X400/X401) Set preset mode. [MODE1]: Recall all saved settings when recalling a preset. [MODE2]: Recall only the pan, tilt, zoom, and focus positions when recalling a preset. [TRACE]: You can use the PTZ TRACE function while the OSD menu is hidden. STANDBY MODE (System - Standby mode) This is the function to move the pan position to the end automatically when the camera enters in the standby mode. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
46
SYSTEM Menu
You can set the menu from the Administrator
menu on a web browser.
For details, see “Installation tab” (page 67) or
“PTZF control tab” (page 88).
IMG FLIP (System - Image flip)
When [IMG FLIP] is set to [ON], the picture is
flipped vertically and picture shift direction by
the pan/tilt operation is also reversed.
After the [IMG FLIP] setting is changed, turn off
the camera and turn it on again to activate the
change.
Note
When the [IMG FLIP] setting is changed, the
coordinates for pan and tilt are flipped and the
following are reset.
– Pan-Tilt limit (PAN-TILT LIMIT)
– Preset
IR RECEIVE (System - IR receive)
If this is turned [OFF], the camera does not
receive signals from the supplied remote
commander.
Be sure to turn this [ON] when you use the
supplied remote commander.
Note
You cannot set [IR RECEIVE] to [OFF] when using
the supplied remote commander. Set [IR
RECEIVE] to [OFF] using the remote controller
(not supplied) or from the Administrator menu
on the web browser.
TALLY LEVEL (System - Tally level) (BRC-
X400/X401)
This allows you to configure the settings related
to the tally lamp on the front of the camera.
Choose from [HIGH], [LOW], and [OFF].
[HIGH]:
When the tally lamp is turned on, it
comes on bright.
[LOW]:
When the tally lamp is turned on, it
comes on dim.
[OFF]:
Even when the tally-lamp-ON command is
received, the tally lamp does not light up.
Note
When [TALLY LEVEL] is set to [OFF], the tally lamp
does not light up.
TELE CONVERT MODE (System - Tele
convert) (BRC-X400/X401, SRG-X402)
You can shoot using 2× magnification.
[OFF]:
Does not use the magnification function.
[2x]:
Uses the magnification function.
Notes
• This is enabled only when the SYSTEM SELECT
switch or the [VIDEO FORMAT] setting is set to
1920×1080.
•
The angle of view when [TELE CONVERT MODE]
is set to [2x] is narrower than when set to [OFF].
• When used with the image stabilizer function,
image quality may be degraded. Set [IMAGE
STABILIZER] (Image stabilizer) to [OFF] if
desired.
HTTP/RTSP
When the setting of the CAMERA SETUP (camera
setup) switch 3 (HTTP/RTSP communication use
setting) on the back of the camera is "OFF"
(MENU), use this setting to turn ON/OFF the
HTTP/RTSP communication. Turn ON the HTTP/
RTSP communication to set the camera with the
web browser or acquire streaming.
[OFF]:
Turn OFF the HTTP/RTSP communication
function of the camera.
[ON]:
Turn ON the HTTP/RTSP communication
function of the camera.
After the [HTTP/RTSP] setting is changed, turn
off the camera and turn it on again to activate the
change.
Note
[HTTP/RTSP] cannot be set on the web browser.
PRESET MODE (Preset - Preset mode)
(BRC-X400/X401)
Set preset mode.
[MODE1]:
Recall all saved settings when recalling
a preset.
[MODE2]:
Recall only the pan, tilt, zoom, and
focus positions when recalling a preset.
[TRACE]:
You can use the PTZ TRACE function
while the OSD menu is hidden.
STANDBY MODE (System – Standby mode)
This is the function to move the pan position to
the end automatically when the camera enters in
the standby mode.