Sony BRC-X400 Operating Instructions - Page 47

PTZ TRACE Menu (BRC-X400/X401), COLOR BAR OVERLAY NAME BRC-X400, VIDEO FORMAT System - Video output

Get Sony BRC-X400 PDF manuals and user guides View all Sony BRC-X400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

[NEUTRAL]: The pan position is not moved automatically. [SIDE]: The pan position is moved to the end automatically. Notes • When the mode is set to [SIDE], the pan position is moved to the end, exceeding the limit even if [PAN LIMIT] is specified. • After the camera is turned on from the standby mode, the camera position moves to the position recorded on PRESET1. COLOR BAR OVERLAY NAME (BRC-X400/ X401) Select whether to display the camera name when the video signal output from the HDMI OUT or SDI OUT terminal is set to color bar. [ON]: Display the camera name. [OFF]: Do not display the camera name. The camera name to display can be changed from [Camera name] on [Common setting] under the Network tab in the Administrator menu, or from [Name] on RM-IP Setup Tool. VIDEO FORMAT (System - Video output) Select the video format of the signal to be output from the HDMI OUT and SDI OUT terminals. The video format can be changed from this menu when the SYSTEM SELECT switch is set to 6. When the SYSTEM SELECT switch is set to a value other than 6, the setting status of the SYSTEM SELECT switch and the SDI format level of the CAMERA SETUP switch are displayed. After the setting is changed, turn off the camera and turn it on again, put the camera in the standby mode and turn it on again, or execute [REBOOT] to reflect the changes. Select the setting from [2160/29.97p], [1080/59.94p A], [1080/59.94p B], [1080/59.94i], [1080/29.97p], [720/59.94p], [720/59.94p VGA], [2160/25p], [1080/50p A], [1080/50p B], [1080/50i], [1080/25p], [720/50p], [2160/23.98p], or [1080/23.98p]. Notes • The video format cannot be changed when the SYSTEM SELECT switch is set to a value other than 6. • For SRG-X400/X402/201M2/X120/HD1M2, you can select 4K only when the 4K Option is installed. REBOOT Reboot the camera. PTZ TRACE Menu (BRC-X400/ X401) PTZ TRACE is a function used to record pan/tilt/ zoom operations, controlled by the remote commander or a remote controller, and then to play back the operations as required. Up to 16 operations can be recorded for up to 180 seconds. You can set the menu from the Administrator menu on a web browser. For details, see "PTZ TRACE (BRC-X400/X401)" (page 90). Notes • If pan and tilt limits are configured in the PAN TILT/ ZOOM menu after recording operations, the pan and tilt limits are not applied upon playback. To use the pan/tilt limit function together, first configure the PAN and TILT settings in the PAN TILT/ZOOM menu and then perform recording operation. • All records will be erased if the IMG FLIP setting is changed. • All PTZ trace records may be erased if you change the video output format. • Playing operations will restore CLEAR IMAGE ZOOM and PAN TILT SLOW to their states held during recording. TRACE NO: Select the TRACE number to record, play back, or delete. RECORD: Record operations. PLAY: Play back the recorded operations. DELETE: Delete the recorded operations. RECORDED TRACE NO: Displays the recorded TRACE numbers. ELAPSED TIME (SEC): Displays the elapsed time during recording or playback in seconds. The HOME button (equivalent to ENTER) on the supplied remote commander corresponds to the joystick button on an optional remote controller. For details, refer to the operating instructions of the remote controller. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
47
[NEUTRAL]:
The pan position is not moved
automatically.
[SIDE]:
The pan position is moved to the end
automatically.
Notes
• When the mode is set to [SIDE], the pan
position is moved to the end, exceeding the
limit even if [PAN LIMIT] is specified.
•
After the camera is turned on from the standby
mode, the camera position moves to the
position recorded on PRESET1.
COLOR BAR OVERLAY NAME (BRC-X400/
X401)
Select whether to display the camera name
when the video signal output from the HDMI OUT
or SDI OUT terminal is set to color bar.
[ON]:
Display the camera name.
[OFF]:
Do not display the camera name.
The camera name to display can be changed
from [Camera name] on [Common setting] under
the Network tab in the Administrator menu, or
from [Name] on RM-IP Setup Tool.
VIDEO FORMAT (System – Video output)
Select the video format of the signal to be output
from the HDMI OUT and SDI OUT terminals.
The video format can be changed from this menu
when the SYSTEM SELECT switch is set to 6.
When the SYSTEM SELECT switch is set to a value
other than 6, the setting status of the SYSTEM
SELECT switch and the SDI format level of the
CAMERA SETUP switch are displayed.
After the setting is changed, turn off the camera
and turn it on again, put the camera in the
standby mode and turn it on again, or execute
[REBOOT] to reflect the changes.
Select the setting from [2160/29.97p],
[1080/59.94p A], [1080/59.94p B], [1080/59.94i],
[1080/29.97p], [720/59.94p], [720/59.94p VGA],
[2160/25p], [1080/50p A], [1080/50p B],
[1080/50i], [1080/25p], [720/50p],
[2160/23.98p], or [1080/23.98p].
Notes
•
The video format cannot be changed when the
SYSTEM SELECT switch is set to a value other
than 6.
• For SRG-X400/X402/201M2/X120/HD1M2, you
can select 4K only when the 4K Option is
installed.
REBOOT
Reboot the camera.
PTZ TRACE Menu (BRC-X400/
X401)
PTZ TRACE is a function used to record pan/tilt/
zoom operations, controlled by the remote
commander or a remote controller, and then to
play back the operations as required. Up to 16
operations can be recorded for up to 180
seconds.
You can set the menu from the Administrator
menu on a web browser.
For details, see "PTZ TRACE (BRC-X400/X401)"
(page 90).
Notes
•
If pan and tilt limits are configured in the PAN TILT/
ZOOM menu after recording operations, the pan and
tilt limits are not applied upon playback. To use the
pan/tilt limit function together, first configure the
PAN and TILT settings in the PAN TILT/ZOOM menu
and then perform recording operation
.
•
All records will be erased if the IMG FLIP setting
is changed.
• All PTZ trace records may be erased if you
change the video output format.
• Playing operations will restore CLEAR IMAGE
ZOOM and PAN TILT SLOW to their states held
during recording.
TRACE NO:
Select the TRACE number to record,
play back, or delete.
RECORD:
Record operations.
PLAY:
Play back the recorded operations.
DELETE:
Delete the recorded operations.
RECORDED TRACE NO:
Displays the recorded
TRACE numbers.
ELAPSED TIME (SEC):
Displays the elapsed time
during recording or playback in seconds.
The HOME button (equivalent to ENTER) on the
supplied remote commander corresponds to the
joystick button on an optional remote controller.
For details, refer to the operating instructions of
the remote controller.