Sony J30 Product Manual (J10, J10SDI, J30, and J30SDI Manual) - Page 30

Using the Remote Commander - used sdi

Get Sony J30 PDF manuals and user guides View all Sony J30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Chapter 4 Playback 4-41 -P3layUbasckinPgroctehdeurResemote Commander Pull off the transparent film covering the battery parts. 4-3-1 How to Change the Lithium Battery 1 Pull out the lithium battery case. Pull the battery case toward you while releasing the lock by plucking it with your fingernail. 4-3-2 Setting Menu When a Remote Commander is used, WIRELESS REMOTE CONTROL, extended menu item 213, must to be set to ON. (It is set to OFF at the factory.) (The following operation is an example of how WIRELESS REMOTE CONTROL is switched from OFF to ON.) 1 Select WIRELESS REMOTE CONTROL, extended menu item 213, to display it. The illustration shows the information displayed in the time data display area and on the monitor connected to the COMPOSITE (SUPER) output connector, SDI (SUPER) output connector (for J10SDI/30SDI only) or DV connector. 2 Set lithium battery in the case so that the + symbol on the battery is facing you. Time data display area Monitor screen REMOTE INTERFACE 137 ❉ 213:WIRELESS-off 501 3 Push the lithium battery case back into its original position. Notes on the Remote Commander • If there is an obstacle between the Remote Commander and the remote control detector, the Remote Commander sometimes does not work properly. Point the Remote Commander at the remote control detector on the front side of the unit. • The effective remote control area is limited. It becomes easier to control the unit the closer you get and if you point the Remote Commander directly at the front of the unit. • Change the battery when the Remote Commander does not work properly. Items without ❉ are omitted. 4-6 Chapter 4 Playback

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
4-1
Playback Procedures
Chapter 4
Playback
4-6
Chapter 4
Playback
4-3
Using the Remote Commander
Pull off the transparent film covering the battery parts.
4-3-1
How to Change the
Lithium Battery
1
Pull out the lithium battery case.
Pull the battery case toward you while releasing
the lock by plucking it with your fingernail.
2
Set lithium battery in the case so that the + symbol
on the battery is facing you.
3
Push the lithium battery case back into its original
position.
Notes on the Remote Commander
• If there is an obstacle between the Remote
Commander and the remote control detector, the
Remote Commander sometimes does not work
properly. Point the Remote Commander at the remote
control detector on the front side of the unit.
• The effective remote control area is limited. It
becomes easier to control the unit the closer you get
and if you point the Remote Commander directly at
the front of the unit.
• Change the battery when the Remote Commander
does not work properly.
4-3-2
Setting Menu
When a Remote Commander is used, WIRELESS
REMOTE CONTROL, extended menu item 213, must
to be set to ON. (It is set to OFF at the factory.)
(The following operation is an example of how
WIRELESS REMOTE CONTROL is switched from
OFF to ON.)
1
Select WIRELESS REMOTE CONTROL,
extended menu item 213, to display it.
The illustration shows the information displayed in
the time data display area and on the monitor
connected to the COMPOSITE (SUPER) output
connector, SDI (SUPER) output connector (for J-
10SDI/30SDI only) or
DV connector.
REMOTE INTERFACE
137
213:WIRELESS-off
501
Items without
are omitted.
Time data display area
Monitor screen