Sony J30 Product Manual (J10, J10SDI, J30, and J30SDI Manual) - Page 47
video processing of the analog video signal.
View all Sony J30 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 47 highlights
Item number Item name 501 STILL TIMER 651 UMID OUTPUT (J-30SDI only) 657 ESSENCE MARK TAPE OUTPUT (J-30SDI only) Settings Sets the time interval from the tape stop mode to the tape protection mode. In order to protect the video heads and the tape, this unit enters the tape protection mode automatically after a certain amount of time has elapsed since the unit entered the tape stop mode (STOP mode or a still picture in jog/shuttle mode). 0.5S ... 8M ... 30M: Set the value in the range 0.5 seconds to 30 minutes. When using the Digital Betacam or MPEG IMX format, select whether or not to output the UMID data recorded on the tape from the SDI output connector and the type of the UMID data if it is output. OFF : Do not output the UMID data. BASIC: Output as the Basic UMID data (32 byte). EXTENDED: Output as the Extended UMID data (64 byte). Notes • Even if EXTENDED is selected, Basic UMID is output if Basic UMID is recorded on the tape being played back. • When menu item 901, VIDEO OUTPUT DATA is set to 8Bit, nothing of UMID is output. When using the Digital Betacam or MPEG IMX format, select whether or not to output essence marks recorded on the tape from the SDI output connector. ON: Output essence marks recorded on the tape. OFF : Do not output essence marks recorded on the tape. Note When menu item 901, VIDEO OUTPUT DATA is set to 8Bit, nothing of essence marks is output. Chapter 7 Setup Menu 658 SHOT MARK ESSENCE When using the Digital Betacam, MPEG IMX or Betacam SX format, select MARK CONVERT whether or not to convert shot marks recorded in the LTC track into essence (J-10SDI/30SDI only) marks and output them from the SDI output connector. ON: Convert shot marks into essence marks and output. OFF : Do not convert shot marks into essence marks. Depending on the type of the detected shot marks, the output essence marks are "_RecStart", "_ShotMark1", or "_ShotMark2". Notes • Of the shot marks, post marks are not converted to essence marks. • Shot mark detection timing depends on playback conditions. • When menu item 901, VIDEO OUTPUT DATA is set to 8 bit, nothing of essence marks is output. 660 710 713a) 715a) 716a) 717a) ESSENCE MARK VANC LINE (J-10SDI/30SDI only) INTERNAL VIDEO SIGNAL GENERATOR VIDEO SETUP REFERENCE LEVEL (When operating in 525 mode) VIDEO GAIN CONTROL CHROMA GAIN CONTROL CHROMA PHASE CONTROL When menu item 658 is set to ON, specify the line into which to insert shot marks converted into essence marks. 12H, 13H, 15H, 16H, 17H 18H, 19H (525-line mode) 09H, 10H, 12H, 13H, 14H, 15H, 16H, 17H , 18H (625-line mode) Select the test signal to be output from the VTR's internal test signal generator. OFF : No test signal is generated. (The VTR operates normally.) CB75: 75% color bar signal Set the setup amount to be added to the composite output signal. Default value: 0.0% 7.5% Adjust the video output level. The only Y signal adjustment is permitted. Default value: 20H Adjust the chroma output level. Default value: 20H Adjust the chroma phase. The only composite output signal adjustment is permitted. Default value: 80H 718a) SETUP LEVEL (525 mode)/ Adjust the setup level (black level). BLACK LEVEL (625 mode) Default value: 0H a) Menu items 713 and 715 to 718 can be used only for video processing of the analog video signal. They cannnot be used for video processing of the digital video signal (SDI/DV output). 7-11 Chapter 7 Setup Menu