Sony SRG360SHE Product Manual Operation Manual SRG-360SHE - Page 29

Operation Using the Supplied Infrared Remote Commander, Before Operating, Turning on the Power

Get Sony SRG360SHE PDF manuals and user guides View all Sony SRG360SHE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Operation Using the Supplied Infrared Remote Commander Before Operating Before operating the camera, check that the camera and peripheral devices are properly installed and connected. For details, see "Setting of the SYSTEM SELECT switch" (page 9), "Installing the Camera" (page 16) and "Connections" (page 19). Note The supplied infrared remote commander may not work correctly near the inverter lighting fixtures. In such a case, try to install the camera far from the inverted luminaire. You can check whether or not the installed location is good for the usage of the infrared remote commander. Turning on the Power SRG-360SHE DC 12 V to AC outlet POWER lights. 1 Connect the camera to an AC outlet using the supplied AC power adaptor and AC power cable or to a LAN connector for PoE+. The power is turned on and the POWER light turns on. The camera automatically pans and tilts to come to the position stored in POSITION 1 when the power is turned on. (Pan/Tilt reset) After this, SDI OUT and HDMI OUT images are output and the NETWORK light comes on. Then, all operations become available (up to two minutes). Note When power is supplied via PoE+, the POWER light does not come on until the initial authentication is completed (the time varies depending on the model; it is approximately one minute). 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
29
Operation Using the Supplied
Infrared Remote Commander
Before Operating
Before operating the camera, check that the camera and
peripheral devices are properly installed and connected.
For details, see “Setting of the SYSTEM SELECT switch”
(page 9), “Installing the Camera” (page 16) and
“Connections” (page 19).
The supplied infrared remote commander may not work
correctly near the inverter lighting fixtures. In such a case,
try to install the camera far from the inverted luminaire.
You can check whether or not the installed location is
good for the usage of the infrared remote commander.
Turning on the Power
1
Connect the camera to an AC outlet using the
supplied AC power adaptor and AC power cable or to
a LAN connector for PoE+.
The power is turned on and the POWER light turns
on.
The camera automatically pans and tilts to come to
the position stored in POSITION 1 when the power is
turned on. (Pan/Tilt reset)
After this, SDI OUT and HDMI OUT images are
output and the NETWORK light comes on. Then, all
operations become available (up to two minutes).
When power is supplied via PoE+, the POWER light does
not come on until the initial authentication is completed
(the time varies depending on the model; it is
approximately one minute).
Note
Note
POWER lights.
to AC outlet
DC 12 V
SRG-360SHE