Sony SRG360SHE Product Manual Operation Manual SRG-360SHE - Page 30

Pan/Tilt and Zoom Operation, Panning and Tilting

Page 30 highlights

2 Turn on the peripheral devices. To switch ON/OFF the video output using the infrared remote commander You can switch ON/OFF the video output using the POWER switch on the infrared remote commander when supplying power to the camera. When the POWER is off, the POWER/NETWORK lamp will go out. If the camera moves in a different direction from the one you intended The camera is preset so that the image output from the camera is rotated toward the right whenever you press the b button. To face the camera toward the opposite direction You might wish to face the camera toward the opposite direction from that of the button you pressed, for example, when you change the direction of the camera while checking the picture on the screen. In such a case, press the 2 (REV) button while holding down the L/R DIRECTION SET button. Arrow button Movement of the camera Setting POWER POWER/NETWORK lights Pan/Tilt and Zoom Operation Panning and Tilting While holding down Press To reset the setting To reset the setting, press the 1 (STD) button while holding down the L/R DIRECTION SET button. Arrow button Movement of the camera Setting While holding down 2 1 Press the POWER switch. You can turn on and off the video output of the unit. When it is ON, the camera automatically resets pan/ tilt and moves the Preset1 position. 2 Press the arrow button to pan or tilt the camera. While checking the picture on the screen, press the desired arrow button. To move the camera little by little, press the button just for a moment. To move the camera in a wide range, press and hold the button. To move the camera diagonally, press the B or b button while holding down the V or v button. To face the camera back to the front Press the HOME button. Press Note The setting above only changes the signal emitted from the infrared remote commander, and does not change the setting of the camera itself. Therefore, repeat the setting for each infrared remote commander if you are using more than one infrared remote commander. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75

30
2
Turn on the peripheral devices.
To switch ON/OFF the video output using the
infrared remote commander
You can switch ON/OFF the video output using the
POWER switch on the infrared remote commander when
supplying power to the camera.
When the POWER is off, the POWER/NETWORK lamp
will go out.
Pan/Tilt and Zoom
Operation
Panning and Tilting
1
Press the POWER switch.
You can turn on and off the video output of the unit.
When it is ON, the camera automatically resets pan/
tilt and moves the Preset1 position.
2
Press the arrow button to pan or tilt the camera.
While checking the picture on the screen, press the
desired arrow button.
To move the camera little by little,
press the button
just for a moment.
To move the camera in a wide range,
press and hold
the button.
To move the camera diagonally,
press the
B
or
b
button while holding down the
V
or
v
button.
To face the camera back to the front
Press the HOME button.
If the camera moves in a different direction from
the one you intended
The camera is preset so that the image output from the
camera is rotated toward the right whenever you press the
b
button.
To face the camera toward the opposite
direction
You might wish to face the camera toward the opposite
direction from that of the button you pressed, for
example, when you change the direction of the camera
while checking the picture on the screen. In such a case,
press the 2 (REV) button while holding down the L/R
DIRECTION SET button.
To reset the setting
To reset the setting, press the 1 (STD) button while holding down
the L/R DIRECTION SET button.
The setting above only changes the signal emitted from
the infrared remote commander, and does not change the
setting of the camera itself. Therefore, repeat the setting
for each infrared remote commander if you are using
more than one infrared remote commander.
POWER
POWER/NETWORK
lights
2
Arrow button
Movement of the
camera
Setting
Arrow button
Movement of the
camera
Setting
Note
While holding
down
Press
While holding
down
Press