Sony STR-DN1030 Operating Instructions (Large File - 11.51 MB) - Page 108

To activate the input after, unsuccessful, check

Get Sony STR-DN1030 PDF manuals and user guides View all Sony STR-DN1030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

3 Press the numeric buttons to enter the numeric code. If more than one code exists, try to enter either one which corresponds to the equipment including TV. Use the tables on page 108-111 to find the numeric code(s) corresponding to the equipment. Note Only the codes in the 500's are valid for the TV button. 4 Press ENT/MEM. Once the numeric code has been verified, the RM SET UP button slowly flashes twice and the remote control automatically exits the programming mode. 5 Repeat steps 1 to 4 to program other equipment. Note The RM SET UP button turns off while a numeric button is pressed. To cancel programming Press RM SET UP during any step. The remote control automatically exits the programming mode. To activate the input after programming Press the programmed button to activate the input you want. If programming is unsuccessful, check the following: • If the RM SET UP button does not light up in step 1, the batteries are weak. Replace both batteries. • If the RM SET UP button flashes 5 times in quick succession while entering the numeric code, an error has occurred. Start again from step 1. The numeric codes corresponding to the equipment and the maker of the equipment Use the numeric codes in the tables below to program non-Sony equipment and also Sony equipment that the remote control is normally unable to control. Since the signal from the remote control received by the equipment differs by its model and the year, more than one numeric code may be assigned to the equipment. If you fail to program your remote control using one of the codes, try using other codes. Notes • The numeric codes are based on the latest information available for each brand. There is a chance, however, that your equipment will not respond to some or all of the codes. • All of the input buttons on this remote control may not be available when used with your particular equipment. To control a CD player Maker SONY DENON JVC KENWOOD MAGNAVOX MARANTZ ONKYO PANASONIC PHILIPS PIONEER TECHNICS YAMAHA Code(s) 101, 102, 103 104, 123 105, 106, 107 108, 109, 110 111, 116 116 112, 113, 114 115 116 117 115, 118, 119 120, 121, 122 To control a DAT deck Maker SONY PIONEER Code(s) 203 219 108US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
108
US
3
Press the numeric buttons to
enter the numeric code.
If more than one code exists, try to enter
either one which corresponds to the
equipment including TV.
Use the tables on page 108–111 to find
the numeric code(s) corresponding to the
equipment.
Note
Only the codes in the 500’s are valid for the TV
button.
4
Press ENT/MEM.
Once the numeric code has been verified,
the RM SET UP button slowly flashes
twice and the remote control
automatically exits the programming
mode.
5
Repeat steps 1 to 4 to program
other equipment.
Note
The RM SET UP button turns off while a numeric
button is pressed.
To cancel programming
Press RM SET UP during any step. The
remote control automatically exits the
programming mode.
To activate the input after
programming
Press the programmed button to activate the
input you want.
If programming is
unsuccessful, check the
following:
•
If the RM SET UP button does not light up
in step 1, the batteries are weak. Replace
both batteries.
•
If the RM SET UP button flashes 5 times in
quick succession while entering the numeric
code, an error has occurred.
Start again from step 1.
Use the numeric codes in the tables below to
program non-Sony equipment and also Sony
equipment that the remote control is normally
unable to control. Since the signal from the
remote control received by the equipment
differs by its model and the year, more than
one numeric code may be assigned to the
equipment. If you fail to program your remote
control using one of the codes, try using other
codes.
Notes
• The numeric codes are based on the latest
information available for each brand. There is a
chance, however, that your equipment will not
respond to some or all of the codes.
• All of the input buttons on this remote control may
not be available when used with your particular
equipment.
To control a CD player
To control a DAT deck
The numeric codes
corresponding to the equipment
and the maker of the equipment
Maker
Code(s)
SONY
101, 102, 103
DENON
104, 123
JVC
105, 106, 107
KENWOOD
108, 109, 110
MAGNAVOX
111, 116
MARANTZ
116
ONKYO
112, 113, 114
PANASONIC
115
PHILIPS
116
PIONEER
117
TECHNICS
115, 118, 119
YAMAHA
120, 121, 122
Maker
Code(s)
SONY
203
PIONEER
219