Stihl TS 410 Instruction Manual - Page 28

Abrasive Cutting Wheels, Composite Cutting Wheels

Get Stihl TS 410 PDF manuals and user guides View all Stihl TS 410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

English Abrasive Cutting Wheels Abrasive cutting wheels are exposed to high loads, especially during hand-held cutting. Only use abrasive cutting wheels that comply with ANSI B 7.1 for hand-held machines and are labeled accordingly. Note that the maximum permissible speed of the cutting wheel must be higher than the maximum spindle speed listed on the wheel guard label. The abrasive cutting wheels that have been developed for STIHL for use on cut-off machines are of high quality and tailored to the intended uses as well as the engine specifications and performance of this cut-off machine. Use of other wheels on your cut-off machine can be extremely dangerous and may result in severe personal injury or death. - Store composite cutting wheels in a frost-free place. - Do not transport a cut-off machine with a abrasive cutting wheel mounted, whether composite or diamond. Transport and storage - Do not expose composite cutting wheels to direct sunshine or other thermal stresses during transport and storage. - Avoid jolts and impacts. - Stack composite cutting wheels flat on a level surface in the original packaging in a dry place where the temperature is as constant as possible. - Do not store composite cutting wheels in the vicinity of aggressive fluids or chemicals. Composite Cutting Wheels Types: - for dry applications - for wet applications Economic benefit is improved and premature wear can be avoided by choosing and using the correct composite cutting wheel. The short name (e.g. "asphalt", "concrete") - on the label and - on the packaging (table with recommended uses) can help to ensure the correct choice. STIHL composite cutting wheels are suitable, depending on the version, for cutting the following materials: - Asphalt - Concrete - Stone - Ductile cast pipes - Steel; STIHL composite cutting wheels cannot be used to cut railway tracks. Do not cut any other materials with your composite cutting wheel. Always use a composite cutting wheel rated for the 26 TS 410, TS 420

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
TS 410, TS 420
English
26
Abrasive cutting wheels are exposed to
high loads, especially during hand-held
cutting.
Only use abrasive cutting wheels that
comply with ANSI B 7.1 for hand-held
machines and are labeled accordingly.
Note that the maximum permissible
speed of the cutting wheel must be
higher than the maximum spindle speed
listed on the wheel guard label.
The abrasive cutting wheels that have
been developed for STIHL for use on
cut-off machines are of high quality and
tailored to the intended uses as well as
the engine specifications and
performance of this cut-off machine. Use
of other wheels on your cut-off machine
can be extremely dangerous and may
result in severe personal injury or death.
Transport and storage
–
Do not expose composite cutting
wheels to direct sunshine or other
thermal stresses during transport
and storage.
–
Avoid jolts and impacts.
–
Stack composite cutting wheels flat
on a level surface in the original
packaging in a dry place where the
temperature is as constant as
possible.
–
Do not store composite cutting
wheels in the vicinity of aggressive
fluids or chemicals.
–
Store composite cutting wheels in a
frost-free place.
–
Do not transport a cut-off machine
with a abrasive cutting wheel
mounted, whether composite or
diamond.
Types:
–
for dry applications
–
for wet applications
Economic benefit is improved and
premature wear can be avoided by
choosing and using the correct
composite cutting wheel. The short
name (e.g. "asphalt", "concrete")
–
on the label and
–
on the packaging (table with
recommended uses)
can help to ensure the correct choice.
STIHL composite cutting wheels are
suitable, depending on the version, for
cutting the following materials:
–
Asphalt
–
Concrete
–
Stone
–
Ductile cast pipes
–
Steel; STIHL composite cutting
wheels cannot be used to cut
railway tracks.
Do not cut any other materials with your
composite cutting wheel. Always use a
composite cutting wheel rated for the
Abrasive Cutting Wheels
Composite Cutting Wheels