Stihl TS 410 Instruction Manual - Page 48

Replacing the V

Get Stihl TS 410 PDF manuals and user guides View all Stihl TS 410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

370BA064 KN English Replacing the V-belt 2 1 0 1 1 N Undo the nuts (1) N Turn the tensioning nut (2) counterclockwise with the combination wrench - approx. 1/4 turn, as far as it will go = 0 370BA037 KN 6 51 1 1 N Unscrew the nuts (1) N Remove the starter cover (5) N Do not remove the "cast arm and guard" (6) - hold it in place on the studs until the starter cover is fitted back in position N Remove the defective V-belt 370BA062 KN 10 10 10 51 1 1 N Fit the starter cover (5) over the studs (10) N Tighten up the nuts (1) by hand 4 3 370BA065 KN 4 3 N Pull the water hose out of the guide in the V-belt guard N Remove screw (3) N Raise the V-belt guard (4) slightly and pull it off to the front N Remove the V-belt from the front pulley 370BA061 KN 9 7 8 N Carefully insert the new V-belt (7) on the V-belt pulley (8) on the engine and the front V-belt pulley (9) NOTICE The belt action must run smoothly. 370BA063 KN N Push the V-belt guard (4) into place N Screw in the bolt (3) and tighten up N Insert the water hose into the guide in the V-belt guard (arrow) from the shut-off cock towards the guard - avoid tight radiuses Continue as described in the chapter "Tensioning the V-belt". 46 TS 410, TS 420

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
TS 410, TS 420
English
46
N
Undo the nuts (1)
N
Turn the tensioning nut (2)
counterclockwise with the
combination wrench –
approx. 1/4 turn, as far as it will
go =
0
N
Pull the water hose out of the guide
in the V
-
belt guard
N
Remove screw (3)
N
Raise the V
-
belt guard (4) slightly
and pull it off to the front
N
Remove the V
-
belt from the front
pulley
N
Unscrew the nuts (1)
N
Remove the starter cover (5)
N
Do not remove the "cast arm and
guard" (6) – hold it in place on the
studs until the starter cover is fitted
back in position
N
Remove the defective V
-
belt
N
Carefully insert the new V
-
belt (7)
on the V
-
belt pulley (8) on the
engine and the front V
-
belt
pulley (9)
NOTICE
The belt action must run smoothly.
N
Fit the starter cover (5) over the
studs (10)
N
Tighten up the nuts (1) by hand
N
Push the V
-
belt guard (4) into place
N
Screw in the bolt (3) and tighten up
N
Insert the water hose into the guide
in the V
-
belt guard (arrow) from the
shut-off cock towards the guard –
avoid tight radiuses
Continue as described in the chapter
“Tensioning the V
-
belt”.
Replacing the V
-
belt
1
1
1
2
370BA037 KN
0
4
3
370BA061 KN
6
370BA062 KN
1
5
1
1
7
8
370BA063 KN
9
10
1
10
10
370BA064 KN
1
5
1
4
3
370BA065 KN