TP-Link T1700X-16TS T1700X-16TSUN V1 User Guide - Page 144

Profile Config

Page 144 highlights

Max Response Time: General Query Source IP: Enter the value of Maximum Response Time of the Query message. Enter the Query Message source IP address. It is FE80::02FF:FFFF:FE00:0001 by default.  MLD Snooping Querier List Select: VLAN ID: Query Interval: Max Response Time: General Query Source IP: Select the Querier you want to change. Displays the VLAN ID. Displays the Query message interval time. Displays the value of Maximum Response Time of the Query message. Displays the Query message source IP address. Note: The MLD Snooping Querier doesn't participate in the MLD Querier Election, but an MLD Snooping Querier will affect the MLD Querier Election in the IPv6 network running MLD because of its relatively smaller IP address. 8.2.6 Profile Config On this page you can configure an MLD profile. Choose the menu Multicast→MLD Snooping→Profile Config to load the following page. Figure 8-18 Profile Config The following entries are displayed on this screen:  Profile Creation Profile ID: Specify the Profile ID you want to create, and it should range from 1 to 999. 133

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265

Max Response Time:
Enter the value of Maximum Response Time of the
Query message.
General Query
Source IP:
Enter the Query Message source IP address. It is
FE80::02FF:FFFF:FE00:0001 by default.
MLD Snooping Querier List
Select:
Select the Querier you want to change.
VLAN ID:
Displays the VLAN ID.
Query Interval:
Displays the Query message interval time.
Max Response Time:
Displays the value of Maximum Response Time of the
Query message.
General Query
Source IP:
Displays the Query message source IP address.
Note:
The MLD Snooping Querier doesn’t participate in the MLD Querier Election, but an MLD Snooping
Querier will affect the MLD Querier Election in the IPv6 network running MLD because of its
relatively smaller IP address.
8.2.6 Profile Config
On this page you can configure an MLD profile.
Choose the menu
Multicast
MLD Snooping
Profile Config
to load the following page.
Figure 8-18 Profile Config
The following entries are displayed on this screen:
Profile Creation
Profile ID:
Specify the Profile ID you want to create, and it should
range from 1 to 999.
133