Yamaha DSP5D Pm5dv2 / Dsp5d Editor Owner's Manual - Page 16

MTRX Send level to MATRIX buses, TO ST To STEREO, VARI/FIXED, SELECT, Channel name, Fader

Get Yamaha DSP5D PDF manuals and user guides View all Yamaha DSP5D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

F MTRX (Send level to MATRIX buses) These bar graphs indicate the send levels of the signals Pre/on (green) sent from the MIX channel to each MATRIX bus. You 6 can also adjust the send levels by dragging a bar graph Pre/off (green) to left or right. The bar graph display will change as follows according Post/on (yellow) 7 to the send position (pre/post) and on/off status of the Post/off (yellow) signal sent from the MIX channel to the MATRIX buses. 8 NOTE You can turn this on/off by clicking the number at left. 9 G TO ST (To STEREO) J This is an on/off switch for the signal sent from the MIX channel to the STEREO bus. K H PAN L Sets the panning of the signal sent from the MIX channel to the STEREO bus. I VARI/FIXED Indicates the type (VARI or FIXED) of the currently selected MIX bus. (This parameter M is for display only. If you want to switch between VARI/FIXED from within PM5D/ DSP5D Editor, use the Mixer Setup window (➥ p.3) If surround mode is enabled, MIX buses that are assigned as surround buses are dis- played with the name of the surround channel (L, R, Ls, Rs ...), and the other MIX buses are displayed as "FIXED." J SELECT Selects the MIX channel for which you want to make settings. This is linked with the MIX [SEL] keys in the MIX section of the PM5D panel. K ON Switches the MIX channel on/off. N L Channel name This is a text box that indicates the channel name. You can also edit the channel name within this text box. M Fader Adjusts the output level of the MIX channel. The current fader value is shown in the numeric box immediately below the fader. The level meter at the right of the fader shows the output level of the signal. The numbers and alphabetical letters at the right of the fader indicate the DCA group and mute groups to which that channel belongs, and show the Recall Safe and Mute Safe status of the channel. (For the significance of the numbers and alphabetical letters, see ➥ p.10). N CUE This button cue-monitors the signal of the MIX channel. This is linked with the MIX [CUE] keys in the MIX section of the PM5D panel. If SOLO is active, this will function as SOLO. 16 PM5DV2/DSP5D Editor Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
PM5DV2/DSP5D Editor Owner’s Manual
16
F
MTRX (Send level to MATRIX buses)
These bar graphs indicate the send levels of the signals
sent from the MIX channel to each MATRIX bus. You
can also adjust the send levels by dragging a bar graph
to left or right.
The bar graph display will change as follows according
to the send position (pre/post) and on/off status of the
signal sent from the MIX channel to the MATRIX
buses.
You can turn this on/off by clicking the number at left.
G
TO ST (To STEREO)
This is an on/off switch for the signal sent from the MIX channel to the STEREO bus.
H
PAN
Sets the panning of the signal sent from the MIX channel to the STEREO bus.
I
VARI/FIXED
Indicates the type (VARI or FIXED) of the currently selected MIX bus. (This parameter
is for display only. If you want to switch between VARI/FIXED from within PM5D/
DSP5D Editor, use the Mixer Setup window (
➥
p.3)
If surround mode is enabled, MIX buses that are assigned as surround buses are dis-
played with the name of the surround channel (L, R, Ls, Rs ...), and the other MIX
buses are displayed as “FIXED.”
J
SELECT
Selects the MIX channel for which you want to make settings. This is linked with the
MIX [SEL] keys in the MIX section of the PM5D panel.
K
ON
Switches the MIX channel on/off.
L
Channel name
This is a text box that indicates the channel name. You can also edit the channel name
within this text box.
M
Fader
Adjusts the output level of the MIX channel. The current fader value is shown in the
numeric box immediately below the fader. The level meter at the right of the fader
shows the output level of the signal.
The numbers and alphabetical letters at the right of the fader indicate the DCA group
and mute groups to which that channel belongs, and show the Recall Safe and Mute
Safe status of the channel. (For the significance of the numbers and alphabetical letters,
see
➥
p.10).
N
CUE
This button cue-monitors the signal of the MIX channel. This is linked with the MIX
[CUE] keys in the MIX section of the PM5D panel. If SOLO is active, this will function
as SOLO.
7
8
9
N
M
J
K
L
6
Pre/on (green)
Pre/off (green)
Post/off (yellow)
Post/on (yellow)
NOTE